PSHLY-B回路电阻测试仪介绍
上传时间： 2013-11-05
上传用户：木子叶1
介绍了用单片机C 语言实现无功补偿中电容组循环投切的基本原理和算法，并举例说明。关键词：循环投切;C51;无功补偿中图分类号： TM76 文献标识码： BAbstract: This paper introduces the aplication of C51 in the controlling of capacitorsuits cycle powered to be on and off in reactive compensation.it illustrate thefondamental principle and algorithm with example.Key words: cycle powered to be on and off; C51; reactive compensation 为提高功率因数，往往采用补偿电容的方法来实现。而电容器的容量是由实时功率因数与标准值进行比较来决定的，实时功率因数小于标准值时，需投入电容组，实时功率因数大于标准值时，则需切除电容组。投切方式的不合理，会对电容器造成损坏，现有的控制器多采用“顺序投切”方式，在这种投切方式下排序在前的电容器组，先投后切；而后面的却后投先切。这不仅使处于前面的电容组经常处于运行状态，积累热量不易散失，影响其使用寿命，而且使后面的投切开关经常动作，同样减少寿命。合理的投切方式应为“循环投切”。这种投切方式使先投入的运行的电容组先退出，后投的后切除，从而使各组电容及投切开关使用机率均等，降低了电容组的平均运行温度，减少了投切开关的动作次数，延长了其使用寿命。
上传时间： 2014-12-27
上传用户：hopy
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
TKS仿真器B系列快速入门
上传时间： 2013-10-31
上传用户：aix008
买的开发板上带的52个应用于实物的程序，希望对大家有帮助
上传时间： 2013-11-04
上传用户：xymbian
一个简单好用的B+树算法实现
上传时间： 2015-01-04
上传用户：缥缈
一个用Basic实现的B-Tree算法
上传时间： 2013-12-30
上传用户：ccclll
一个用Java applet实现的B-Tree算法
上传时间： 2013-12-25
上传用户：qiao8960
用C++实现的B-Tree算法
上传时间： 2014-01-20
上传用户：jiahao131
用Borland C写的B-Tree算法
上传时间： 2014-12-05
上传用户：xzt
