一直以來， 電子電路斷路器( E C B ) 都是由一個MOSFET、一個 MOSFET 控制器和一個電流檢測電阻器所組成的。
上传时间： 2013-10-18
上传用户：qwerasdf
为简化总线式RS485隔离器的设计，提出基于脉冲变压器的总线式RS485隔离器的技术方案。该方案具有简单实用、无需电源、无需考虑数据流向、在有限范围内波特率自适应、底层用户群体易于理解和掌控等特点。给出了基本实验电路和脉冲变压器的主要设计依据。基于脉冲变压器的总线式RS485隔离器，尤其适合工业环境下半双工的A、B两线制RS485通信网的升级改造，其基本思想也适用于全双工的W、X、Y、Z四线制RS485/RS422通信网。
上传时间： 2013-10-07
上传用户：lizx30340
在静电传感器测量气/固两相流参数的基础上，以J.B.Gajewski教授的成果为基础，对电容的计算进行了研究。将静电传感器电极与屏蔽罩间的电容cp看作圆柱型电容，对其建立的静电传感器数学模型中的感应电极与屏蔽罩间电容值进行探讨，并得到了这个电容的计算式。
上传时间： 2014-12-24
上传用户：erkuizhang
电子、电气产品的设计，必须保证在一定的电磁环境中能正常工作，既满足标准规定的抗干扰极限值要求，在受到一定的电磁干扰时，无性能降级或故障；又要满足标准规定的电磁辐射极限值的要求，对电磁环境不构成污染。所以，产品设计之初，就要从分析产品预期的电磁环境、干扰源、耦合途径和敏感部件入手，采用相应的技术措施，抑制干扰源、切断或削弱耦合途径，增强敏感部件的抗干扰能力等。文中详细介绍了一款485通讯隔离产品从辐射超标到顺利通过FCC CLASS B认证，在原理设计、PCB制板等多方面所做的各项改进措施。文中所提到的方法及规则，对产品EMC设计具有很大的参考及指导意义。
上传时间： 2013-10-24
上传用户：sz_hjbf
AL-LJ(K)系列零序电流互感器 保定奥兰电气科技有限责任公司生产的AL-LJ(K)系列零序电流互感器经电力工业部电气设备质量检测中心检测，质量优于国标GB1208-1997《电流互感器》，具有精度高，线性度好，运行可靠，安装方便，外型美观等特点。 零序电流互感器（电缆型）的孔径范围为Ф40～Ф360，有各种容量、变比、准确限值系数，可与小电流接地选线装置、继电器、仪表等配套使用，实现对系统的检测和保护。装置具有灵敏度高，线性度好等优点。产品分整体式和组合式两类。互感器采用工程塑料外壳、树脂浇注全密封；外型美观、安装方便、节省安装空间、规格品种多，可适用各种保护装置和电力系统各种运行方式（中性点接地，中性点不接地，大电阻接地，小电阻接地和消弧线圈接地）的需要。 空格：用于小电流接地选线装置 A：与DD11/60型继电器配合使用 J：用于微机型继电保护 B：与DL11/0.2型继电器配合使用 保定市奥兰电气科技有限责任公司开发生产的零序电流互感器是一种套在电缆上的CT，它的一次绕组为穿过CT内孔的三相一次导体电缆，它的一次电流是一次三相电流的向量和（在正常、三相平衡时为0），当发生一次系统单相接地时三相平衡关系被打破，这时零序电流互感器的二次就有电流输出，供给保护装置，实现保护和监控。 零序电流互感器的一次绝缘就是电缆自身绝缘，所以这种零序电流互感器可以套在任一电压等级的电缆上。
标签： 零序电流互感器
上传时间： 2013-10-30
上传用户：fengzimili
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间： 2013-11-18
上传用户：hulee
For a variety of reasons, it is desirable to charge batteriesas rapidly as possible. At the same time, overchargingmust be limited to prolong battery life. Such limitation ofovercharging depends on factors such as the choice ofcharge termination technique and the use of multi-rate/multi-stage charging schemes. The majority of batterycharger ICs available today lock the user into one fixedcharging regimen, with at best a limited number ofcustomization options to suit a variety of application needsor battery types. The LTC®1325 addresses these shortcomingsby providing the user with all the functionalblocks needed to implement a simple but highly flexiblebattery charger (see Figure 1) which not only addressesthe issue of charging batteries but also those of batteryconditioning and capacity monitoring.
上传时间： 2013-10-19
上传用户：royzhangsz
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
简易负离子发生器负离子增加，对人有催眠、止汗、镇痛、增进食欲，使人精神爽快，消除疲劳的作用。图1是负离子发生器电路图。220V交流市电经D1整流后向C3和C2充电，当C2充电至氖泡导通并触发SCR导通时，C3经SCR、B的L1放电，经B感应升压后，由D2反向整流得8kV直流高压使发生器M的分子电离而产生负离子。调整R3的阻值可以改变触发频率和输出电压。调整时必须注意安全，更换元件需拨下电源插头
标签： 负离子发生器
上传时间： 2013-10-29
上传用户：731140412
