While simplicity and high effi ciency (for cool running) areno longer optional features in isolated power supplies, itis traditionally diffi cult to achieve both. Achieving higheffi ciency often requires the use of advanced topologiesand home-brewed secondary synchronous rectifi cationschemes once reserved only for higher power applications.This only adds to the parts count and to the designcomplexity associated with the reference and optocouplercircuits typically used to maintain isolation. Fortunately, abreakthrough IC makes it possible to achieve both high efficiency and simplicity in a synchronous fl yback topology.The LT®3825 simplifi es and improves the performance oflow voltage, high current fl yback supplies by providingprecise synchronous rectifi er timing and eliminating theneed for optocoupler feedback while maintaining excellentregulation and superior loop response.
上传时间： 2013-10-16
上传用户：wayne595
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
上传时间： 2014-12-24
上传用户：jasson5678
Handheld designers often grapple with ways to de-bounceand control the on/off pushbutton of portable devices.Traditional de-bounce designs use discrete logic, fl ipflops, resistors and capacitors. Other designs includean onboard microprocessor and discrete comparatorswhich continuously consume battery power. For highvoltage multicell battery applications, a high voltageLDO is needed to drive the low voltage devices. All thisextra circuitry not only increases required board spaceand design complexity, but also drains the battery whenthe handheld device is turned off. Linear Technology addressesthis pushbutton interface challenge with a pairof tiny pushbutton controllers.
上传时间： 2013-11-18
上传用户：ZJX5201314
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上传时间： 2013-10-19
上传用户：bakdesec
序号 参数 数据 单位 参数 说 明 . 输 入 参 数 变 量 1 umin V 交流输入电压最小值 2 umax V 交流输入电压最大值 3 fl Hz 电网频率 4 f kHz 开关频率 5 UO V 直流输出电压 6 PO W 输出功率 7 η % 电源效率 8 Z 0.5 损耗分配系数 9 UFB V 反馈电压
上传时间： 2013-10-14
上传用户：小码农lz
•概述•主要特性的深入研究• RS08KB特性及应用• S08SF特性及应用• S08SV/fl特性及应用•易于使用的开发工具•样品和工具上市时间•获取优惠50％的DEMO9RS08KB12
上传时间： 2013-11-12
上传用户：siying
The LTC®3207/LTC3207-1 is a 600mA LED/Camera driverwhich illuminates 12 Universal LEDs (ULEDs) and onecamera fl ash LED. The ULEDs are considered universalbecause they may be individually turned on or off, setin general purpose output (GPO) mode, set to blink at aselected on-time and period, or gradate on and off at aselected gradation rate. This device also has an externalenable (ENU) pin that may be used to blink, gradate, orturn on/off the LEDs without using the I2C bus. This may beuseful if the microprocessor is in sleep or standby mode. Ifused properly, these features may save valuable memoryspace, programming time, and reduce the I2C traffi c.
上传时间： 2014-01-04
上传用户：LANCE
PCB 被动组件的隐藏特性解析 传统上，EMC一直被视为「黑色魔术（black magic）」。其实，EMC是可以藉由数学公式来理解的。不过，纵使有数学分析方法可以利用，但那些数学方程式对实际的EMC电路设计而言，仍然太过复杂了。幸运的是，在大多数的实务工作中，工程师并不需要完全理解那些复杂的数学公式和存在于EMC规范中的学理依据，只要藉由简单的数学模型，就能够明白要如何达到EMC的要求。本文藉由简单的数学公式和电磁理论，来说明在印刷电路板（PCB）上被动组件（passivecomponent）的隐藏行为和特性，这些都是工程师想让所设计的电子产品通过EMC标准时，事先所必须具备的基本知识。导线和PCB走线导线（wire）、走线（trace）、固定架……等看似不起眼的组件，却经常成为射频能量的最佳发射器（亦即，EMI的来源）。每一种组件都具有电感，这包含硅芯片的焊线（bond wire）、以及电阻、电容、电感的接脚。每根导线或走线都包含有隐藏的寄生电容和电感。这些寄生性组件会影响导线的阻抗大小，而且对频率很敏感。依据LC 的值（决定自共振频率）和PCB走线的长度，在某组件和PCB走线之间，可以产生自共振（self-resonance），因此，形成一根有效率的辐射天线。在低频时，导线大致上只具有电阻的特性。但在高频时，导线就具有电感的特性。因为变成高频后，会造成阻抗大小的变化，进而改变导线或PCB 走线与接地之间的EMC 设计，这时必需使用接地面（ground plane）和接地网格（ground grid）。导线和PCB 走线的最主要差别只在于，导线是圆形的，走线是长方形的。导线或走线的阻抗包含电阻R和感抗XL = 2πfl，在高频时，此阻抗定义为Z = R + j XL j2πfl，没有容抗Xc = 1/2πfC存在。频率高于100 kHz以上时，感抗大于电阻，此时导线或走线不再是低电阻的连接线，而是电感。一般而言，在音频以上工作的导线或走线应该视为电感，不能再看成电阻，而且可以是射频天线。
上传时间： 2013-11-16
上传用户：极客
