Abstract: What can be simpler than designing with CMOS and BiCMOS? These technologies are very easy to use butthey still require careful design. This tutorial discusses the odd case of circuits that seem to work but exhibit somepeculiar behaviors—including burning the designer's fingers!
上传时间： 2013-11-03
上传用户：dick_sh
Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上传时间： 2013-11-08
上传用户：xianglee
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Automotive power systems are unforgiving electronicenvironments. Transients to 90V can occur when thenominal voltage range is 10V to 15V (ISO7637), along withbattery reversal in some cases. It’s fairly straightforwardto build automotive electronics around this system, butincreasingly end users want to operate portable electronics,such as GPS systems or music/video players,and to charge their Li-Ion batteries from the automotivebattery. To do so requires a compact, robust, effi cientand easy-to-design charging system
上传时间： 2013-11-04
上传用户：wfl_yy
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
/*--------- 8051内核特殊功能寄存器 -------------*/ sfr ACC = 0xE0; //累加器 sfr B = 0xF0; //B 寄存器 sfr PSW = 0xD0; //程序状态字寄存器 sbit CY = PSW^7; //进位标志位 sbit AC = PSW^6; //辅助进位标志位 sbit F0 = PSW^5; //用户标志位0 sbit RS1 = PSW^4; //工作寄存器组选择控制位 sbit RS0 = PSW^3; //工作寄存器组选择控制位 sbit OV = PSW^2; //溢出标志位 sbit F1 = PSW^1; //用户标志位1 sbit P = PSW^0; //奇偶标志位 sfr SP = 0x81; //堆栈指针寄存器 sfr DPL = 0x82; //数据指针0低字节 sfr DPH = 0x83; //数据指针0高字节 /*------------ 系统管理特殊功能寄存器 -------------*/ sfr PCON = 0x87; //电源控制寄存器 sfr AUXR = 0x8E; //辅助寄存器 sfr AUXR1 = 0xA2; //辅助寄存器1 sfr WAKE_CLKO = 0x8F; //时钟输出和唤醒控制寄存器 sfr CLK_DIV = 0x97; //时钟分频控制寄存器 sfr BUS_SPEED = 0xA1; //总线速度控制寄存器 /*----------- 中断控制特殊功能寄存器 --------------*/ sfr IE = 0xA8; //中断允许寄存器 sbit EA = IE^7; //总中断允许位 sbit ELVD = IE^6; //低电压检测中断控制位 8051
上传时间： 2013-10-30
上传用户：yxgi5
TLC2543是TI公司的12位串行模数转换器，使用开关电容逐次逼近技术完成A/D转换过程。由于是串行输入结构，能够节省51系列单片机I/O资源；且价格适中，分辨率较高，因此在仪器仪表中有较为广泛的应用。 TLC2543的特点 （1）12位分辩率A/D转换器； （2）在工作温度范围内10μs转换时间； （3）11个模拟输入通道； （4）3路内置自测试方式； （5）采样率为66kbps； （6）线性误差±1LSBmax； （7）有转换结束输出EOC； （8）具有单、双极性输出； （9）可编程的MSB或LSB前导； （10）可编程输出数据长度。 TLC2543的引脚排列及说明 TLC2543有两种封装形式：DB、DW或N封装以及FN封装，这两种封装的引脚排列如图1，引脚说明见表1 TLC2543电路图和程序欣赏 #include<reg52.h> #include<intrins.h> #define uchar unsigned char #define uint unsigned int sbit clock=P1^0; sbit d_in=P1^1; sbit d_out=P1^2; sbit _cs=P1^3; uchar a1,b1,c1,d1; float sum,sum1; double sum_final1; double sum_final; uchar duan[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; uchar wei[]={0xf7,0xfb,0xfd,0xfe}; void delay(unsigned char b) //50us { unsigned char a; for(;b>0;b--) for(a=22;a>0;a--); } void display(uchar a,uchar b,uchar c,uchar d) { P0=duan[a]|0x80; P2=wei[0]; delay(5); P2=0xff; P0=duan[b]; P2=wei[1]; delay(5); P2=0xff; P0=duan[c]; P2=wei[2]; delay(5); P2=0xff; P0=duan[d]; P2=wei[3]; delay(5); P2=0xff; } uint read(uchar port) { uchar i,al=0,ah=0; unsigned long ad; clock=0; _cs=0; port<<=4; for(i=0;i<4;i++) { d_in=port&0x80; clock=1; clock=0; port<<=1; } d_in=0; for(i=0;i<8;i++) { clock=1; clock=0; } _cs=1; delay(5); _cs=0; for(i=0;i<4;i++) { clock=1; ah<<=1; if(d_out)ah|=0x01; clock=0; } for(i=0;i<8;i++) { clock=1; al<<=1; if(d_out) al|=0x01; clock=0; } _cs=1; ad=(uint)ah; ad<<=8; ad|=al; return(ad); } void main() { uchar j; sum=0;sum1=0; sum_final=0; sum_final1=0; while(1) { for(j=0;j<128;j++) { sum1+=read(1); display(a1,b1,c1,d1); } sum=sum1/128; sum1=0; sum_final1=(sum/4095)*5; sum_final=sum_final1*1000; a1=(int)sum_final/1000; b1=(int)sum_final%1000/100; c1=(int)sum_final%1000%100/10; d1=(int)sum_final%10; display(a1,b1,c1,d1); } }
上传时间： 2013-11-19
上传用户：shen1230
#include<iom16v.h> #include<macros.h> #define uint unsigned int #define uchar unsigned char uint a,b,c,d=0; void delay(c) { for for(a=0;a<c;a++) for(b=0;b<12;b++); }; uchar tab[]={ 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,
上传时间： 2013-10-21
上传用户：13788529953
