虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

detours-src

  • 一种A_D转换接口电路及其调试软件设计

    介绍了A/ D 转换接口电路的一种设计方法,并在VC+ + 610 环境下编写调试A/ D 转换电路的程序。

    标签: A_D 转换接口 电路 调试

    上传时间: 2013-10-11

    上传用户:hanli8870

  • 0~12V 700mA高性能稳压电源设计

    本人在实际工作中也遇到了同样的需求,为此自己设计了一款可以从0V 起调的宽范围稳压电源电路,并制做完成。经多年来的实际使用,电源工作非常稳定,整体性能非常理想。好东西不能自己独厚,这里介绍给大家。

    标签: 12V 700 mA 性能

    上传时间: 2013-11-22

    上传用户:jennyzai

  • 使用H桥变压器驱动器,充电超级电容器

    Abstract: With its small size and large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.

    标签: H桥变压器 驱动器 充电 超级电容器

    上传时间: 2013-10-20

    上传用户:2728460838

  • 汽车应用的电源控制

    Abstract: This article discusses the requirements and design considerations for automotive applications, including those for enginecontrol, infotainment, and body electronics. It also discusses several Maxim devices that are ideal for automotive applications.

    标签: 汽车应用 电源控制

    上传时间: 2013-10-27

    上传用户:jiangxiansheng

  • G3-PLC技术使电动汽车智能化充电

    Abstract: This article explores criteria necessary for reliable communication between electric vehicles (EVs) and electric vehicleservice equipment (EVSE). Data will demonstrate that a G3-PLC system has already met the criteria established by the automotiveand utility industries. Multiple international tests prove that a G3-PLC implementation is the optimal low-frequency solution.

    标签: PLC 电动汽车 智能化 充电

    上传时间: 2014-12-24

    上传用户:逗逗666

  • 数控大功率精密恒流源设计

    介绍了一种在大功率运放()PA549基础上的数控精密恒流源设计方法。该方法采用闭环控制,大功率运放提高了输出电流,同时具有过温、电流过载保护功能,输出电流精度达到0.05000.

    标签: 数控 大功率 精密恒流源

    上传时间: 2013-11-18

    上传用户:x18010875091

  • 基于GA与L-M优化算法的变压器故障诊断研究

    利用MATLAB环境建立一个用于变压器故障诊断的BP网络模型。首先利用具有全局寻优功能的遗传算法对BP神经网络的初始权值和阈值进行优化,然后采用L-M(Levenberg-Marquardt)优化算法对BP神经网络进行训练,从而达到加快网络训练速度,避免训练过程陷入局部极小点的目的。最后,详细记录网络的实际输出,并与期望输出做对比研究,最终证实了此网络达到了设计要求,可用于变压器的故障诊断。

    标签: L-M 优化算法 变压器 故障诊断

    上传时间: 2013-10-11

    上传用户:hz07104032

  • 利用Multisim求任意激励下电路的响应

    结合教学实践,采用Muhisim元件库中提供的分段线性信号源来实现任意激励源,具有简单、易用、适应性广等特点。给出了任意激励源的设置方法,包括数据点输人和数据文件输人方法,并通过例子来说明该方法在求任意激励下动态电路响应中的应用。

    标签: Multisim 激励 电路

    上传时间: 2013-11-15

    上传用户:yl8908

  • 光纤传感器中光源的驱动与控制

    该方案通过采用恒流源、有源区温度控制以及波长锁定等技术方法来实现DFB LD 的稳频驱动及控制。试验表明,该方案可使得激光器的注入电流控制精度优于0.05%,温度控制精度达0.01 ℃,输出光谱线宽度< 0.2 nm. 此方案可广泛应用于光纤传感及通信等相关场合。

    标签: 光纤传感器 光源 驱动 控制

    上传时间: 2013-10-24

    上传用户:lwq11

  • 佳生CCFL可调光护眼灯电路原理分析

    理想的阅读光源应具备白色光、无闪烁、亮度可调及光照均匀等特性,佳生护眼灯是一款亮度在600-1300LX范围内六挡可调,采用全新冷阴极荧光灯管(即CCFL),寿命可达15000小时的护眼灯,依实物测绘的原理图见附图所示,供参考。

    标签: CCFL 可调光 护眼灯

    上传时间: 2013-10-17

    上传用户:3到15