为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
通过比较各种隔离数字通信的特点和应用范围，指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口，有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路，说明设计过程中的注意事项，对光收发模块的电压特性和频率特性进行全面试验，并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明，该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上传时间： 2014-01-10
上传用户：gundan
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
提出了一种以ARM微处理器为控制核心的远程无线视频监控终端的设计方案，其监控终端的硬件设计包括视频采集处理、中央管理控制、无线传输3个模块。并给出了监控终端的软件开发平台和开发模式的系统启动代码、嵌入式Linux系统移植以及驱动程序和应用程序。测试结果表明，该监控终端设计方案合理、有效，基本满足监控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上传时间： 2013-11-13
上传用户：wanqunsheng
一个24c16的读写程序（已经调试过）(arens) //////////////////////////////////////////////////////////////// //24c16读写驱动程序，FM24C16A-AT24C16中文资料pdf //=-------------------------------------------------------------------------------/*模块调用:读数据:read(unsigned int address)写数据:write(unsigned int address,unsigned char dd) dd为要写的 数据字节*///---------------------------------------------------------------------------------- sbit sda=P3^0;sbit scl=P3^1; sbit a0=ACC^0; //定义ACC的位，利用ACC操作速度最快sbit a1=ACC^1;sbit a2=ACC^2;sbit a3=ACC^3;sbit a4=ACC^4;sbit a5=ACC^5;sbit a6=ACC^6;sbit a7=ACC^7; //--------------------------------------------------------------------------------------#pragma disablevoid s24(void) //起始函数{_nop_(); scl=0; sda=1; scl=1; _nop_(); sda=0; _nop_(); _nop_(); scl=0; _nop_(); _nop_(); sda=1;
上传时间： 2013-10-31
上传用户：fdfadfs
针对嵌入式机器视觉系统向独立化、智能化发展的要求，介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析，对国内外的几款智能相机进行比较。综合技术发展现状，提出基于FPGA+DSP模式的硬件平台，并提出智能相机的发展方向。分析结果表明，该系统设计可以实现脱离PC运行，完成图像获取与分析，并作出相应输出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上传时间： 2013-11-14
上传用户：无聊来刷下
针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的ddS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言编写出源程序，在Virtex-II Pro 开发板上成功实现了整个系统。测试结果表明该系统正确实现了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the ddS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上传时间： 2013-11-19
上传用户：neu_liyan
为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2013-10-28
上传用户：jyycc
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2013-10-10
上传用户：zxc23456789
