Abstract: There are differences between the operation of low-frequency AC transformers and electronic transformersthat supply current to MR16 lamps, and there are also differences in the current draw for MR16 halogen lamps andMR16 LED lamps. These contrasts typically prevent an MR16 LED lamp from operating with most electronictransformers. This article explains how a high-brightness (HB) LED driver optimized for MR16 lamps will allow LEDlamps to be compatible with most electronic transformers.A similar version of this article appeared on Display Plus, July 7, 2012 and in German in Elektronikpraxis, October 1,2012.
上传时间： 2013-10-14
上传用户：playboys0
Abstract: Some power architectures require the power supply sequencer (or system manager) to controldownstream power MOSFETs to allow power to flow into branch circuits. This application note explains howsystem power sequencing and level shifting can be accomplished using a low-voltage system manager
上传时间： 2013-11-02
上传用户：wys0120
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
As the performance of many handheld devices approachesthat of laptop computers, design complexity also increases.Chief among them is thermal management—how doyou meet increasing performance demands while keepinga compact and small product cool in the user’s hand?For instance, as battery capacities inevitably increase,charge currents will also increase to maintain or improvetheir charge times. Traditional linear regulator-based batterychargers will not be able to meet the charge currentand effi ciency demands necessary to allow a product torun cool. What is needed is a switching-based chargerthat takes just about the same amount of space as a linearsolution—but without the heat.
上传时间： 2013-11-23
上传用户：lu2767
Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
The CAT823, CAT824, and CAT825 provide basic reset and monitoring functions for the electronic systems. Each device monitors the system voltage and maintains a reset output until that voltage reaches the device’s specified trip value and then maintains the reset output active condition until the device’s internal timer, after a minimum timer of 140ms; toallow the systems power supply to stabilize.
上传时间： 2014-11-18
上传用户：BOBOniu
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
