A simple C program to strobe the LEDsvia Port D. The strobe rate is to be set by adjusting the voltage drop over a potentiometer that is sampled by an ADC.
上传时间： 2014-01-09
上传用户：lifangyuan12
An assembly to strobe the LEDsvia Port D. The strobe rate is to be set by adjusting the voltage drop over a potentiometer that is sampled by an ADC
上传时间： 2015-03-20
上传用户：13681659100
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC converter. The digital adjustmentmethods are with a digital-to-analog converter (DAC), a trim pot (digital potentiometer), and PWM output of a microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
上传时间： 2013-11-20
上传用户：zycidjl
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-07
上传用户：Yue Zhong
This paper presents an interactive technique that produces static hairstyles by generating individual hair strands of the desired shape and color, subject to the presence of gravity and collisions. A variety of hairstyles can be generated by adjusting the wisp parameters, while the deformation is solved efficiently, accounting for the effects of gravity and collisions. Wisps are generated employing statistical approaches. As for hair deformation, we propose a method which is based on physical simulation concepts but is simplified to efficiently solve the static shape of hair. On top of the statistical wisp model and the deformation solver, a constraint-based styler is proposed to model artificial features that oppose the natural flow of hair under gravity and hair elasticity, such as a hairpin. Our technique spans a wider range of human hairstyles than previously proposed methods, and the styles generated by this technique are fairly realistic.
标签： interactive hairstyles generating technique
上传时间： 2013-12-20
上传用户：sssl
西安电子科技大学 硕士学位论文 《基于DSP的无刷直流电机高性能调速系统的研究》 作者姓名：张焱 Research on BLDC High Performance Speed-adjusting System Based on DSP
标签： Speed-adjusti Performance Research BLDC
上传时间： 2016-08-18
上传用户：日光微澜
The applet illustrates the behaviour of binary search trees, Searching and Sorting Algorithms, Self-adjusting Binary Search Trees, Symmetric binary B-trees,聽Data structure and maintenance algorithms
标签： illustrates Algorithms Searching behaviour
上传时间： 2017-04-10
上传用户：helmos
This paper analyzes the vector control theory of asynchronous motors based on the magnetic orientation of motor rotors, and its mathematical model is made. Then the variable frequency vector speed-adjusting experimental system is built with the DSP TMS320F2812 which works as the core control chip and intelligent power module.
标签： asynchronous orientati the analyzes
上传时间： 2013-12-08
上传用户：shinesyh
Computational models are commonly used in engineering design and scientific discovery activities for simulating complex physical systems in disciplines such as fluid mechanics, structural dynamics, heat transfer, nonlinear structural mechanics, shock physics, and many others. These simulators can be an enormous aid to engineers who want to develop an understanding and/or predictive capability for complex behaviors typically observed in the corresponding physical systems. Simulators often serve as virtual prototypes, where a set of predefined system parameters, such as size or location dimensions and material properties, are adjusted to improve the performance of a system, as defined by one or more system performance objectives. Such optimization or tuning of the virtual prototype requires executing the simulator, evaluating performance objective(s), and adjusting the system parameters in an iterative, automated, and directed way. System performance objectives can be formulated, for example, to minimize weight, cost, or defects; to limit a critical temperature, stress, or vibration response; or to maximize performance, reliability, throughput, agility, or design robustness. In addition, one would often like to design computer experiments, run parameter studies, or perform uncertainty quantification (UQ). These approaches reveal how system performance changes as a design or uncertain input variable changes. Sampling methods are often used in uncertainty quantification to calculate a distribution on system performance measures, and to understand which uncertain inputs contribute most to the variance of the outputs. A primary goal for Dakota development is to provide engineers and other disciplinary scientists with a systematic and rapid means to obtain improved or optimal designs or understand sensitivity or uncertainty using simulationbased models. These capabilities generally lead to improved designs and system performance in earlier design stages, alleviating dependence on physical prototypes and testing, shortening design cycles, and reducing product development costs. In addition to providing this practical environment for answering system performance questions, the Dakota toolkit provides an extensible platform for the research and rapid prototyping of customized methods and meta-algorithms
标签： Optimization and Uncertainty Quantification
上传时间： 2016-04-08
上传用户：huhu123456
