1、 支持USB 1.1通讯协议；2、 支持高速（Full Speed、12Mbps ）和低速（Low Speed、1.5Mbps ）传输；3、 6MHz晶体，锁相环PLL振荡器提供高速、低速所需时钟源；4、 支持3个端口（endpoint），可独立编程为IN 或 OUT端口。5、 PS/2：支持PS/2协议（eg.鼠标），与USB复用。
上传时间： 2013-11-03
上传用户：hbsunhui
The PCA82C250 and PCA82C251 are advanced transceiver products for use in automotive and general industrialapplications with transfer rates up to 1 Mbit/s. They support the differential bus signal representation beingdescribed in the international standard for in-vehicle CAN high-speed applications (ISO 11898). Controller AreaNetwork (CAN) is a serial bus protocol being primarily intended for transmission of control related data between anumber of bus nodes.
上传时间： 2013-11-24
上传用户：Alick
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
上传时间： 2013-10-13
上传用户：cicizoe
这一颗，我们学习如何让跑马灯自动按照我们预定的顺序进行。这种控制在工控场合经常用到。这个程序里，我们预先定义了一个变化的顺序speedcode，每跑一圈灯就根据预定设置的表格数据来决定下一圈的跑马速度。这样我们就实现了按照预定的顺序自动变化运行。请看代码：-----------------------------------#define uchar unsigned char //定义一下方便使用#define uint unsigned int#define ulong unsigned long#include <reg52.h> //包括一个52 标准内核的头文件sbit P10 = P1^0; //头文件中没有定义的IO 就要自己来定义了sbit P11 = P1^1;sbit P12 = P1^2;sbit P13 = P1^3;bit ldelay=0; //长定时溢出标记,预置是0uchar speed=10; //设置一个变量保存跑马灯的移动速度uchar code speedcode[10]={3,1,5,12,3,20,2,10,1,4}; //10 个预定义的速度char code dx516[3] _at_ 0x003b;//这是为了仿真设置的//可编程自动控制跑马灯void main(void) // 主程序{uchar code ledp[4]={0xfe,0xfd,0xfb,0xf7};//预定的写入P1 的值uchar ledi; //用来指示显示顺序uchar i;RCAP2H =0x10; //赋T2 的预置值0x1000，溢出30 次就是1 秒钟RCAP2L =0x00;TR2=1; //启动定时器ET2=1; //打开定时器2 中断EA=1; //打开总中断
上传时间： 2013-11-20
上传用户：ming529
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
针对运行中火车测速运用多普勒效应采用DSP 设计雷达测速系统并阐述了其基本设计思想与工作原理给出系统硬件软件设计结构和原理图改善了原有光电测速精度提高了系统工作稳定性和可靠性经实验证明DSP 采集板工作稳定测速效果好关键词DSP; 雷达测速; 多普勒效应 On Board DSP-Based Radar Speed Measurement System TANG Wei, SUN Zhi-fang, CHEN Quan (Dept.of computer Science,Yangtze University,Jingzhou 434023,China)Abstract: This paper presents a DSP-based train speed measurement by using Doppler radar. The structure of the system is introduced.The hardware and software are also discussed.Key words: DSP; rader speed measurement; doppler principle
上传时间： 2013-10-27
上传用户：003030
中文版详情浏览：http://www.elecfans.com/emb/fpga/20130715324029.html Xilinx UltraScale:The Next-Generation Architecture for Your Next-Generation Architecture The Xilinx® UltraScale™ architecture delivers unprecedented levels of integration and capability with ASIC-class system- level performance for the most demanding applications. The UltraScale architecture is the industr y's f irst application of leading-edge ASIC architectural enhancements in an All Programmable architecture that scales from 20 nm planar through 16 nm FinFET technologies and beyond, in addition to scaling from monolithic through 3D ICs. Through analytical co-optimization with the X ilinx V ivado® Design Suite, the UltraScale architecture provides massive routing capacity while intelligently resolving typical bottlenecks in ways never before possible. This design synergy achieves greater than 90% utilization with no performance degradation. Some of the UltraScale architecture breakthroughs include: • Strategic placement (virtually anywhere on the die) of ASIC-like system clocks, reducing clock skew by up to 50% • Latency-producing pipelining is virtually unnecessary in systems with massively parallel bus architecture, increasing system speed and capability • Potential timing-closure problems and interconnect bottlenecks are eliminated, even in systems requiring 90% or more resource utilization • 3D IC integration makes it possible to build larger devices one process generation ahead of the current industr y standard • Greatly increased system performance, including multi-gigabit serial transceivers, I/O, and memor y bandwidth is available within even smaller system power budgets • Greatly enhanced DSP and packet handling The Xilinx UltraScale architecture opens up whole new dimensions for designers of ultra-high-capacity solutions.
标签： UltraScale Xilinx 架构
上传时间： 2013-11-13
上传用户：瓦力瓦力hong
Consumer display applications commonly use high-speed LVDS interfaces to transfer videodata. Spread-spectrum clocking can be used to address electromagnetic compatibility (EMC)issues within these consumer devices. This application note uses Spartan®-6 FPGAs togenerate spread-spectrum clocks using the DCM_CLKGEN primitive.
上传时间： 2014-12-28
上传用户：yan2267246
