数字射频存储器(Digital Radio FreqlJencyr：Memory DRFM)具有对射频信号和微波信号的存储、处理及传输能力，已成为现代雷达系统的重要部件。现代雷达普遍采用了诸如脉冲压缩、相位编码等更为复杂的信号处理技术，DRFM由于具有处理这些相干波形的能力，被越来越广泛地应用于电子对抗领域作为射频频率源。目前，国内外对DRFM技术的研究还处于起步阶段，DRFM部件在采样率、采样精度及存储容量等方面，还不能满足现代雷达信号处理的要求。 本文介绍了DRFM的量化类型、基本组成及其工作原理，在现有的研究基础上提出了一种便于工程实现的设计方法，给出了基于现场可编程门阵列(Field Programmable Gate Array FPGA)实现的幅度量化DRFM设计方案。本方案的采样率为1 GHz、采样精度12位，具体实现是采用4个采样率为250 MHz的ADC并行交替等效时间采样以达到1 GHz的采样率。单通道内采用数字正交采样技术进行相干检波，用于保存信号复包络的所有信息。利用FPGA器件实现DRFM的控制器和多路采样数据缓冲器，采用硬件描述语言(Very High Speed}lardware Description Language VHDL)实现了DRFM电路的FPGA设计和功能仿真、时序分析。方案中采用了大量的低压差分信号(Low Voltage Differential Signaling LVDS)逻辑的芯片，从而大大降低了系统的功耗，提高了系统工作的可靠性。本文最后对采用的数字信号处理算法进行了仿真，仿真结果证明了设计方案的可行性。 本文提出的基于FPGA的多通道DRFM系统与基于专用FIFO存储器的DRFM相比，具有更高的性能指标和优越性。
上传时间： 2013-06-01
上传用户：lanwei
BGA布线指南 BGA CHIP PLACEMENT AND ROUTING RULE BGA是PCB上常用的组件，通常CPU、NORTH BRIDGE、SOUTH BRIDGE、AGP CHIP、CARD BUS CHIP…等，大多是以bga的型式包装，简言之，80﹪的高频信号及特殊信号将会由这类型的package内拉出。因此，如何处理BGA package的走线，对重要信号会有很大的影响。 通常环绕在BGA附近的小零件，依重要性为优先级可分为几类： 1. by pass。 2. clock终端RC电路。 3. damping（以串接电阻、排组型式出现；例如memory BUS信号） 4. EMI RC电路（以dampin、C、pull height型式出现；例如USB信号）。 5. 其它特殊电路（依不同的CHIP所加的特殊电路；例如CPU的感温电路）。 6. 40mil以下小电源电路组（以C、L、R等型式出现；此种电路常出现在AGP CHIP or含AGP功能之CHIP附近，透过R、L分隔出不同的电源组）。 7. pull low R、C。 8. 一般小电路组（以R、C、Q、U等型式出现；无走线要求）。 9. pull height R、RP。 中文DOC，共5页，图文并茂
上传时间： 2013-04-24
上传用户：cxy9698
MPC755 and MPC745 PowerPC microprocessors are high-performance, low-power, 32-bit implementations of
上传时间： 2013-05-27
上传用户：330402686
用fpga实现的DA转换器，有说明和源码，VDHL文件。\\r\\nA PLD Based Delta-Sigma DAC\\r\\nDelta-Sigma modulation is the simple, yet powerful,\\r\\ntechnique responsible for the extraordinary\\r\\nperformance and low cost of today s audio CD\\r\\nplayers. The simplest Delta-Sigm
上传时间： 2013-08-22
上传用户：dudu1210004
Abstract: This application note describes how sampling clock jitter (time interval error or "TIE jitter") affectsthe performance of delta-sigma digital-to-analog converters (DACs). New insights explain the importanceof separately specifying low-frequency (< 2x passband frequency) and high-frequency or wideband (> 2xpassband frequency) jitter tolerance in these devices. The article also provides an application example ofa simple highly jittered cycle-skipped sampling clock and describes a method for generating a properbroadband jittered clock. The document then goes on to compare Maxim's audio DAC jitter tolerance tocompetitor audio DACs. Maxim's exceptionally high jitter tolerance allows very simple and low-cost sampleclock implementations.
上传时间： 2013-10-25
上传用户：banyou
The MAX2870 ultra-wideband phase-locked loop (PLL) and voltagecontrol oscillator (VCO) can operate in both integer-N and fractional-Nmodes, similar to the Analog Devices ADF4350 wideband synthesizer.This application note compares the MAX2870 and ADF4350 registers andloop filter design in detail. Users who already familiar with ADF4350 canuse this application note as a quick design reference.
上传时间： 2014-12-23
上传用户：变形金刚
The MAX5713/MAX5714/MAX5715 4-channel, low-power,8-/10-/12-bit, voltage-output digital-to-analog converters(DACs) include output buffers and an internal referencethat is selectable to be 2.048V, 2.500V, or 4.096V. TheMAX5713/MAX5714/MAX5715 accept a wide supplyvoltage range of 2.7V to 5.5V with extremely low power(3mW) consumption to accommodate most low-voltageapplications. A precision external reference input allowsrail-to-rail operation and presents a 100kI (typ) load toan external reference.
上传时间： 2013-12-23
上传用户：ArmKing88
The MAX4968/MAX4968A are 16-channel, high-linearity,high-voltage, bidirectional SPST analog switches with18I (typ) on-resistance. The devices are ideal for use inapplications requiring high-voltage switching controlledby a low-voltage control signal, such as ultrasound imagingand printers. The MAX4968A provides integrated40kI (typ) bleed resistors on each switch terminal todischarge capacitive loads. Using HVCMOS technology,these switches combine high-voltage bilateral MOSswitches and low-power CMOS logic to provide efficientcontrol of high-voltage analog signals.
上传时间： 2013-10-09
上传用户：yepeng139
Abstract: Class D amplifiers are typically very efficient, making them ideal candidates for portable applications that require longbattery life and low thermal dissipation. However, electromagnetic interference (EMI) is an issue that commonly accompanies theClass D switching topology. Active-emissions limiting reduces radiated emissions and enables "filterless" operation, allowingdesigners to create small, efficient portable applications with low EMI.
上传时间： 2013-11-23
上传用户：哈哈hah
Abstract: Build a composite amplifier featuring high gain, wide bandwidth, good DC accuracy and low distortion
上传时间： 2014-12-23
上传用户：JasonC
