Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
标签: Creating Machines Mentor State
上传时间: 2013-10-08
上传用户:wangzhen1990
R7732_7733_7735是Richpower公司推出的高效AC TO DC 电源PWM控制芯片,最大功率可以做到75W;如有需求请联系我电话:021-54262182EXT 114 (Eric) QQ :1187337351
上传时间: 2013-11-20
上传用户:xz85592677
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间: 2013-10-31
上传用户:caiguoqing
Abstract: Field-programmable gate arrays (FPGAs) are used in a wide variety of applications and end markets, including digital signalprocessing, medical imaging, and high-performance computing. This application note outlines the issues related to powering FPGAs.It also discusses Maxim's solutions for powering Altera® FPGAs.
上传时间: 2013-11-02
上传用户:zhaoman32
长电c2383 TO-92L
上传时间: 2013-11-09
上传用户:wvbxj
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上传时间: 2013-10-23
上传用户:wuchunzhong
Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with high-side inductor current
上传时间: 2013-11-20
上传用户:stewart·
Piezoelectric motors are used in digital cameras for autofocus,zooming and optical image stabilization. Theyare relatively small, lightweight and effi cient, but theyalso require a complicated driving scheme. Traditionally,this challenge has been met with the use ofseparatecircuits, including a step-up converter and an oversizedgeneric full-bridge drive IC. The resulting high componentcount and large board space are especially problematicin the design of cameras for ever shrinking cell phones.The LT®3572 solves these problems by combining astep-up regulator and a dual full-bridge driver in a 4mm× 4mm QFN package. Figure 1 shows a typical LT3572Piezo motor drive circuit. A step-up converter is usedto generate 30V from a low voltage power source suchas a Li-Ion battery or any input power source within thepart’s wide input voltage range of 2.7V to 10V. The highoutput voltage of the step-up converter, adjustable upto 40V, is available for the drivers at the VOUT pin. Thedrivers operate in a full-bridge fashion, where the OUTAand OUTB pins are the same polarity as the PWMA andPWMB pins, respectively, and the OUTA and OUTB pinsare inverted from PWMA and PWMB, respectively. Thestep-up converter and both Piezo drivers have their ownshutdown control. Figure 2 shows a typical layout
上传时间: 2013-11-18
上传用户:hulee
Alkaline batteries are convenient because they’re easy tofi nd and relatively inexpensive, making them the powersource of choice for portable instruments and devicesused for outdoor recreation. Their long shelf life alsomakes them an excellent choice for emergency equipmentthat may see infrequent use but must be ready to go on amoment’s notice. It is important that the DC/DC convertersin portable devices operate over the widest possiblebattery voltage range to extend battery run time, and thussave the user from frequent battery replacement.
上传时间: 2014-12-24
上传用户:569342831
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间: 2013-11-07
上传用户:moerwang