一种实用的微机自动配料秤系统:介绍一种由单片机构成的配料秤。叙述了秤的传感器、变送器、信号的变换、硬件原理、软件流程以及和DCS 系统构成的单回路调节系统,此系统可广泛地应用于各行业的配料控制中。关键词:配料秤 单片机 单回路调节系统 DCS 系统 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上传时间： 2013-10-12
上传用户：zwei41
基于单片机控制的二氧化碳浓度测试计:基于CDM4161二氧化碳气体浓度测试模块以及ATtiny26单片机,提出了一种二氧化碳浓度测试计的设计方案。该方案具有硬件电路简单、成本低、可靠性高、测量准确等优点，具有较高的实用价值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上传时间： 2013-11-14
上传用户：zjwangyichao
51单片机工程师实例设计程序集-（20种常见应用整编） \7290\ ;ZLG7290例程*\7290a\ ;ZLG7290汇编例程*\bell\ ;蜂鸣器音乐例程*\buzz\ ;蜂鸣器响例程*\eeprom\ ;读EEPROM并显示例程*\ex26a_lcd\ ;16×2LCD模块例程*\ex36a_lcm\ ;128×64点阵LCD模块例程*\KEY_IO\ ;直连KEY和LED例程\led_light\ ;直连LED例程*\lin_park\ ;lin模块的原码及例程。\lin\ ;LIN总线例程\rs232\ ;RS232例程(包括PC端和书上了串口例程)\USB1.1\ ;USB1.1例程(包括PC端)\RS485\ ;RS485例程\USB2.0\ ;USB2.0例程(有3个，包括PC端)\TCPIP\ ;基于ETHERNET的TCPIP例程\RTC\ ;时钟显示例程\CAN_SELF\ ;CAN自发自收例程 外中断1\CAN\ ;CAN例程\USBPACK 2.0\ ;USB2.0PC例程 注意：带*程序为MON51调试程序。在MON时程序下载后停不下来，可以按一下RSE按钮复位一下。
上传时间： 2013-10-13
上传用户：雨出惊人love
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a starter kit demo board.
上传时间： 2013-11-24
上传用户：363186
提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制Con trol System of Stepp ingMotor Ba sed on AT89C52 ChipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing motor controller.KEY WORDS: Chip microcomputer; Stepp ingmotor; DCSSR; Real2time control
标签： Control System ingMot Stepp
上传时间： 2013-11-19
上传用户：leesuper
The 87C576 includes two separate methods of programming theEPROM array, the traditional modified Quick-Pulse method, and anew On-Board Programming technique (OBP).Quick Pulse programming is a method using a number of devicepins in parallel (see Figure 1) and is the traditional way in which87C51 family members have been programmed. The Quick-Pulsemethod supports the following programming functions:– program USER EPROM– verify USER EPROM– program KEY EPROM– program security bits– verify security bits– read signature bytesThe Quick-Pulse method is quite easily suited to standardprogramming equipment as evidenced by the numerous vendors of87C51 compatible programmers on the market today. Onedisadvantage is that this method is not well suited to programming inthe embedded application because of the large number of signallines that must be isolated from the application. In addition, parallelsignals from a programmer would need to be cabled to theapplication’s circuit board, or the application circuit board wouldneed to have logic built-in to perform the programming functions.These requirements have generally made in-circuit programmingusing the modified Quick Pulse method impractical in almost all87C51 family applications.
上传时间： 2013-10-21
上传用户：xiaozhiqban
CAN与RS232转换节点的设计与实现 介绍将CAN总线接口与RS232总线接口相互转换的设计方法和2种总线电平转换关系，实现CAN总线与各模块的接口设计，制定了相应的软硬件设计方案，并给出软件设计流程图以及部分硬件设计原理图。为CAN总线与RS232总线互联提供了一种方法，对CAN总线与RS232总线接口设备的互联和广泛应用的实现具有重要意义。关键词：CAN总线；RS-232总线；串行通信Design and Realization of CAN and RS232 Transformation NodeZHOU Wei, CHENG Xiao-hong(Information Institute, Wuhan University of Technology, Wuhan 430070)【Abstract】This paper introduces one design method of the CAN bus interface and the RS232 bus interface interconversion, emphasizes two kindof bus level transformation relations, realizes the CAN bus and various modules connection design, formulates the design proposal of correspondingsoftware and hardware, and gives the flow chart of software design as well as the partial schematic diagram of hardware design. It providesonemethod for the CAN bus and the RS232 bus interconnection, has the vital significance to widespread application realization of the CAN busand theRS232 bus interface equipment interconnection.【Key words】CAN bus; RS-232 bus; serial communication
上传时间： 2013-11-04
上传用户：leesuper
P C B 可测性设计布线规则之建议― ― 从源头改善可测率PCB 设计除需考虑功能性与安全性等要求外，亦需考虑可生产与可测试。这里提供可测性设计建议供设计布线工程师参考。1. 每一个铜箔电路支点，至少需要一个可测试点。如无对应的测试点，将可导致与之相关的开短路不可检出，并且与之相连的零件会因无测试点而不可测。2. 双面治具会增加制作成本，且上针板的测试针定位准确度差。所以Layout 时应通过Via Hole 尽可能将测试点放置于同一面。这样就只要做单面治具即可。3. 测试选点优先级：A.测垫(Test Pad) B.通孔(Through Hole) C.零件脚(Component Lead) D.贯穿孔(Via Hole)(未Mask)。而对于零件脚，应以AI 零件脚及其它较细较短脚为优先，较粗或较长的引脚接触性误判多。4. PCB 厚度至少要62mil(1.35mm)，厚度少于此值之PCB 容易板弯变形，影响测点精准度，制作治具需特殊处理。5. 避免将测点置于SMT 之PAD 上，因SMT 零件会偏移，故不可靠，且易伤及零件。6. 避免使用过长零件脚(>170mil(4.3mm))或过大的孔(直径>1.5mm)为测点。7. 对于电池(Battery)最好预留Jumper，在ICT 测试时能有效隔离电池的影响。8. 定位孔要求：(a) 定位孔(Tooling Hole)直径最好为125mil(3.175mm)及其以上。(b) 每一片PCB 须有2 个定位孔和一个防呆孔(也可说成定位孔,用以预防将PCB反放而导致机器压破板)，且孔内不能沾锡。(c) 选择以对角线，距离最远之2 孔为定位孔。(d) 各定位孔(含防呆孔)不应设计成中心对称,即PCB 旋转180 度角后仍能放入PCB,这样,作业员易于反放而致机器压破板)9. 测试点要求：(e) 两测点或测点与预钻孔之中心距不得小于50mil(1.27mm)，否则有一测点无法植针。以大于100mil(2.54mm)为佳，其次是75mil(1.905mm)。(f) 测点应离其附近零件(位于同一面者)至少100mil，如为高于3mm 零件，则应至少间距120mil，方便治具制作。(g) 测点应平均分布于PCB 表面，避免局部密度过高，影响治具测试时测试针压力平衡。(h) 测点直径最好能不小于35mil(0.9mm)，如在上针板，则最好不小于40mil(1.00mm)，圆形、正方形均可。小于0.030”(30mil)之测点需额外加工，以导正目标。(i) 测点的Pad 及Via 不应有防焊漆(Solder Mask)。(j) 测点应离板边或折边至少100mil。(k) 锡点被实践证实是最好的测试探针接触点。因为锡的氧化物较轻且容易刺穿。以锡点作测试点，因接触不良导致误判的机会极少且可延长探针使用寿命。锡点尤其以PCB 光板制作时的喷锡点最佳。PCB 裸铜测点，高温后已氧化，且其硬度高，所以探针接触电阻变化而致测试误判率很高。如果裸铜测点在SMT 时加上锡膏再经回流焊固化为锡点，虽可大幅改善，但因助焊剂或吃锡不完全的缘故，仍会出现较多的接触误判。
上传时间： 2014-01-14
上传用户：cylnpy
三種方法讀取鍵值 使用者設計行列鍵盤介面，一般常採用三種方法讀取鍵值。 中斷式 在鍵盤按下時產生一個外部中斷通知CPU，並由中斷處理程式通過不同位址讀資料線上的狀態判斷哪個按鍵被按下。 本實驗採用中斷式實現使用者鍵盤介面。 掃描法 對鍵盤上的某一行送低電位，其他為高電位，然後讀取列值，若列值中有一位是低，表明該行與低電位對應列的鍵被按下。否則掃描下一行。 反轉法 先將所有行掃描線輸出低電位，讀列值，若列值有一位是低表明有鍵按下；接著所有列掃描線輸出低電位，再讀行值。 根據讀到的值組合就可以查表得到鍵碼。4x4鍵盤按4行4列組成如圖電路結構。按鍵按下將會使行列連成通路，這也是見的使用者鍵盤設計電路。 //-----------4X4键盘程序--------------// uchar keboard(void) { uchar xxa,yyb,i,key; if((PINC&0x0f)!=0x0f) //是否有按键按下 {delayms(1); //延时去抖动 if((PINC&0x0f)!=0x0f) //有按下则判断 { xxa=~(PINC|0xf0); //0000xxxx DDRC=0x0f; PORTC=0xf0; delay_1ms(); yyb=~(PINC|0x0f); //xxxx0000 DDRC=0xf0; //复位 PORTC=0x0f; while((PINC&0x0f)!=0x0f) //按键是否放开 { display(data); } i=4; //计算返回码 while(xxa!=0) { xxa=xxa>>1; i--; } if(yyb==0x80) key=i; else if(yyb==0x40) key=4+i; else if(yyb==0x20) key=8+i; else if(yyb==0x10) key=12+i; return key; //返回按下的键盘码 } } else return 17; //没有按键按下 }
上传时间： 2013-11-12
上传用户：a673761058
