AC/DC适配器(ADAPTER)高频电子变压器的设计有很多制约条件，比如空间体积、热的问题、转换器的效率、电磁干扰、PWM控制IC、性价比等。所以磁心选用受到一定的限制，不像一般资料中介绍的满足功率容量即可，选择的余地不大。所以本文不讲解具体的磁心选择，仅利用计算软件对磁心的功率容量进行校验。目前与NOTEBOOK和LCD配套的中高档ADAPTER工作频率在60KHz~100KHz左右。变压器的绕组已用上了三重绝缘线，再要做小变压器已经有难度。我们知道小型化开关变压器有两种方法：一、提高开关频率，带来的问题是对EMI的控制有一定难度；二、选用更高饱和磁通密度的磁心材料，如TDK公司的PC95和PE33 见表（1）。如果在100℃时Bsat能达到450mT~500mT，那么我们在设计开关变压器时就能使用更少的圈数，减少铜损，同时又能提高初级绕组的电感量，降低峰值电流，减少开关管的能量损耗，从而减少开关变压器的体积，进一步地实现ADAPTER的小型化。
上传时间： 2013-08-04
上传用户：bjgaofei
FPGA设计全流程：Modelsim>>Synplify.Pro>>ISE\\r\\n第一章 Modelsim编译Xilinx库\\r\\n第二章 调用Xilinx CORE-Generator\\r\\n第三章 使用Synplify.Pro综合HDL和内核\\r\\n第四章 综合后的项目执行\\r\\n第五章 不同类型结构的仿真
上传时间： 2013-08-20
上传用户：cuibaigao
微弱信号检测装置 四川理工学院 刘鹏飞、梁天德、曾学明 摘要： 本设计以TI的Launch Pad为核心板，采用锁相放大技术设计并制作了一套微弱信号检测装置，用以检测在强噪声背景下已知频率微弱正弦波信号的幅度值，并在液晶屏上数字显示出所测信号相应的幅度值。实验结果显示其抗干扰能力强，测量精度高。 关键词：强噪声；微弱信号；锁相放大；Launch Pad Abstract: This design is based on the Launch Pad of TI core board, using a lock-in amplifier technique designed and produced a weak signal detection device, to measure the known frequency sine wave signal amplitude values of the weak in the high noise background, and shows the measured signal amplitude of the corresponding value in the liquid crystal screen. Test results showed that it has high accuracy and strong anti-jamming capability. Keywords: weak signal detection; lock-in-amplifier; Launch Pad 1、引言 随着现代科学技术的发展，在科研与生产过程中人们越来越需要从复杂高强度的噪声中检测出有用的微弱信号，因此对微弱信号的检测成为当前科研的热点。微弱信号并不意味着信号幅度小，而是指被噪声淹没的信号，“微弱”也仅是相对于噪声而言的。只有在有效抑制噪声的条件下有选择的放大微弱信号的幅度，才能提取出有用信号。微弱信号检测技术的应用相当广泛，在生物医学、光学、电学、材料科学等相关领域显得愈发重要。 2、方案论证 针对微弱信号的检测的方法有很多，比如滤波法、取样积分器、锁相放大器等。下面就针对这几种方法做一简要说明。 方案一：滤波法。 在大部分的检测仪器中都要用到滤波方法对模拟信号进行一定的处理，例如隔离直流分量，改善信号波形，防止离散化时的波形混叠，克服噪声的不利影响，提高信噪比等。常用的噪声滤波器有：带通、带阻、高通、低通等。但是滤波方法检测信号不能用于信号频谱与噪声频谱重叠的情况，有其局限性。虽然可以对滤波器的通频带进行调节，但其噪声抑制能力有限，同时其准确性与稳定性将大打折扣。
上传时间： 2013-11-04
上传用户：lty6899826
The core voltages for FPGAs are moving lower as a resultof advances in the fabrication process. The newest FPGAfamily from Altera, the Stratix® II, now requires a corevoltage of 1.2V and the Stratix, Stratix GX, HardCopy®Stratix and CycloneTM families require a core voltage of1.5V. This article discusses how to power the core and I/Oof low voltage FPGAs using the latest step-down switchmode controllers from Linear Technology Corporation.
上传时间： 2013-10-08
上传用户：wangfei22
Speed and accuracy don’t always go hand-in-handin DC/DC converter systems—that is, until now. TheLTC3811 is a dual output, fi xed frequency current modeDC/DC switching regulator controller designed for one oftoday’s most demanding power supply applications: highcurrent, low voltage processor core supplies.
上传时间： 2013-11-21
上传用户：aix008
光伏发电是未来新能源发电重要方向之一，而光伏变流器是光伏发电系统的核心。介绍一种基于微网理念的光伏变流器设计。以该变流器为核心的光伏发电系统可以看做一个小型的微网系统。该系统能根据外部电网情况，工作于并网模式和离网模式。介绍了该系统的各个组成部件的设计以及变流器主电路部分器件的选型。最后，由实验样机进行测试。试验结果验证了电路拓扑结构及控制方案的可行性，也说明了系统参数设计方法的正确性。 Abstract: Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
上传时间： 2014-12-24
上传用户：Shaikh
为了提高PCB板制作的效率，改变传统的化学腐蚀制板工艺，使用机械仿形铣制作电路板的方法，设计了以ATMEGA16单片机为核心部件的PCB板雕刻机控制系统。其中包括PCB雕刻机的基本功能、主要硬件电路设计和软件的实现流程，并给出了相关设计电路。重点分析了雕刻机步进电机的驱动电路以及主轴电机的驱动电路，该雕刻机经实际运行，系统工作良好，可有效提高PCB板的制作效率。 Abstract: In order to improve the efficiency of production of PCB board and change the traditional chemical etching plates， using of mechanical copying milling method makes circuit boards，this paper introduces the PCB engraving machine control system used ATMEGA16 microcomputer as the core components. It includes basic function， the hardware circuit design and software realization process， and gives the corresponding circuit design.It analyses the drive circuit of engrawing machine stepper motor and spindle motor in detail. This engraving machine by practical operation， the system works well， which can effectively improve the production efficiency of PCB board.
上传时间： 2013-10-17
上传用户：liangliang123
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
针对煤矿井下调度及紧急救援系统的需求，以DTMF编解码模块为核心，设计了具有自动拨号功能的新型电话系统。该系统利用MT8880对DTMF信号的编解码功能实现一键拨号和远程设置，通过检测振铃和忙音信号，完成自动摘机和挂机过程，配合AGC等外围电路达到话音清晰流畅的效果。 Abstract: To meet the demand for mine scheduling and emergency rescue system， with using DTMF signal codec as the core， a new telephone system was designed with automatic dialing function. In the system， the DTMF signal encoding and decoding function of MT8880 was used to achieve one-touch dialing and remote setting. The circuit detects the ringing and busy signal， and then completes automatic off-hook and hangup. With AGC(Automatic Gain Control) and other peripheral circuits， the voice was regulated to a clear and smooth effect.
上传时间： 2014-11-18
上传用户：ly1994
为了提高传统温度控制系统的性能，将PID控制理论与嵌入式系统相结合，采用瑞萨电子公司的H8S/2166作为核心处理器，AD公司的AD7705以及热敏电阻温度传感器作为温度检测单元，利用4×6小键盘、LCD显示器和S1D13305液晶控制器达到良好的人机交互，设计出了一个应用于化工领域的嵌入式实时温度控制系统。相比于传统温度控制系统，该系统提供了更强的计算能力和可扩展能力，采用增量PID控制算法实现复杂控制。通过实验，该系统能达到0.1 ℃的温度控制精度以及小于120 s的温度稳定时间。 Abstract: In order to improve the performance of conventional temperature control system， combining PID control theory with embedded systems， using the Renesas Electronics Corp. H8S/2166 micro-controller as a core processors， AD7705 and thermistor temperature sensor as a temperature detection unit and 4×6 small keyboard， LCD and S1D13305 LCD controller as a good human-computer interaction， this paper designed an embedded real-time temperature control system which is applied in chemical industry. Compared with conventional temperature control system， this system provides more computing power and extensibility， and adopts PID control algorithm for complex control. Through the experiment， the system can reach temperature control accuracy of 0.1 ℃ and temperature stabilization time of less than 120 seconds.
上传时间： 2014-12-26
上传用户：003030
