The main oscillator allows either a crystal or single-ended input clock signal. Cost-sensitiveapplications typically use an external crystal with the on-chip oscillator circuit since it is the mostcost-effective solution. It is also possible to use the internal oscillator to clock the device after theboot process has completed.
标签： Stellaris Clocking Options for
上传时间： 2013-10-14
上传用户：pol123
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上传时间： 2013-11-10
上传用户：liaofamous
用C51写的普通拼音输入法源程序代码:原作使用了一个二维数组用以查表，我认为这样比较的浪费空间，而且每个字表的索引地址要手工输入，效率不高。所以我用结构体将其改写了一下。就是大家现在看到的这个。 因为代码比较的大，共有6,000多汉字，这样就得要12,000 byte来存放GB内码，所以也是没办法的.编译结果约为3000h,因为大部分是索引表，代码优化几乎无效。 在Keil C里仿真芯片选用的是华邦的W77E58，它有32k ROM, 256B on-chip RAM, 1K on-chip SRAM (用DPTR1指针寻址,相当于有1K的片上xdata)。条件有限，没有上片试验，仿真而已。 打算将其移植到AVR上，但CodeAVRC与IAR EC++在结构体、指针的定义使用上似乎与C51不太一样，现在还未搞定。还希望在这方面有经验的网友能给予指导。 #include<stdio.h> char * py_ime(char *); void main(void){ while(1) { char input_string[]="yI"; xdata char chinese_string[255]; sprintf(chinese_string,"%s",py_ime(input_string)); }}
上传时间： 2013-10-30
上传用户：cainaifa
PK51是为8051系列单片机所设计的开发工具，支持所有8051系列衍生产品，，支持带扩展存储器和扩展指令集（例如Dallas390/5240/400,Philips 51MX,Analog Devices MicroConverters）的新设备,以及支持很多公司的一流的设备和IP内核,比如Analog Devices, Atmel, Cypress Semiconductor, Dallas Semiconductor, Goal, Hynix, Infineon, Intel, NXP(founded by Philips), OKI, Silicon Labs,SMSC, STMicroeleectronics,Synopsis, TDK, Temic, Texas Instruments,Winbond等。通过PK51专业级开发工具，可以轻松地了解8051的On-chip peripherals与及其它关键特性。
上传时间： 2013-10-09
上传用户：1109003457
The AT89C52 is a low-power, high-performance CMOS 8-bit microcomputer with 8Kbytes of Flash programmable and erasable read only memory (PEROM). The deviceis manufactured using Atmel’s high-density nonvolatile memory technology and iscompatible with the industry-standard 80C51 and 80C52 instruction set and pinout.The on-chip Flash allows the program memory to be reprogrammed in-system or by aconventional nonvolatile memory programmer. By combining a versatile 8-bit CPUwith Flash on a monolithic chip, the Atmel AT89C52 is a powerful microcomputerwhich provides a highly-flexible and cost-effective solution to many embedded controlapplications.
上传时间： 2013-11-10
上传用户：1427796291
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上传时间： 2013-10-26
上传用户：yuzsu
Keil C51 V8 专业开发工具（PK51） PK51是为8051系列单片机所设计的开发工具，支持所有8051系列衍生产品，，支持带扩展存储器和扩展指令集（例如Dallas390/5240/400,Philips 51MX,Analog Devices MicroConverters）的新设备,以及支持很多公司的一流的设备和IP内核,比如Analog Devices, Atmel, Cypress Semiconductor, Dallas Semiconductor, Goal, Hynix, Infineon, Intel, NXP(founded by Philips), OKI, Silicon Labs,SMSC, STMicroeleectronics,Synopsis, TDK, Temic, Texas Instruments,Winbond等。 通过PK51专业级开发工具，可以轻松地了解8051的On-chip peripherals与及其它关键特性。 The PK51专业级开发工具包括… l μVision Ø 集成开发环境 Ø 调试器 Ø 软件模拟器 l Keil 8051扩展编译工具 Ø AX51宏汇编程序 Ø ANSI C编译工具 Ø LX51 连接器 Ø OHX51 Object-HEX 转换器 l Keil 8051编译工具 Ø A51宏汇编程序 Ø C51 ANSI C编译工具 Ø BL51 代码库连接器 Ø OHX51 Object-HEX 转换器 Ø OC51 集合目标转换器 l 目标调试器 Ø FlashMON51 目标监控器 Ø MON51目标监控器 Ø MON390 (Dallas 390)目标监控器 Ø MONADI (Analog Devices 812)目标监控器 Ø ISD51 在系统调试 l RTX51微实时内核 你应该考虑PK51开发工具包,如果你… l 需要用8051系列单片机来开发 l 需要开发 Dallas 390 或者 Philips 51MX代码 l 需要用C编写代码 l 需要一个软件模拟器或是没有硬件仿真器 l 需要在单芯片上基于小实时内核创建复杂的应用
上传时间： 2013-10-30
上传用户：yy_cn
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
上传时间： 2014-12-31
上传用户：zhuoying119
