针对嵌入式机器视觉系统向独立化、智能化发展的要求，介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析，对国内外的几款智能相机进行比较。综合技术发展现状，提出基于FPGA+DSP模式的硬件平台，并提出智能相机的发展方向。分析结果表明，该系统设计可以实现脱离PC运行，完成图像获取与分析，并作出相应输出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上传时间： 2013-11-14
上传用户：无聊来刷下
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2014-01-24
上传用户：s363994250
Abstract: As industrial control systems (ICSs) have become increasingly connected and use more off-the-shelfcomponents, new vulnerabilities to cyber attacks have emerged. This tutorial looks at three types of ICSs:programmable logic controllers (PLCs), supervisory control and data acquisition (SCADA) systems, anddistributed control systems (DCSs), and then discusses security issues and remedies. This document alsoexplains the benefits and limitations of two cryptographic solutions (digital signatures and encryption) andelaborates on the reasons for using security ICs in an ICS to support cryptography.
上传时间： 2013-10-09
上传用户：woshinimiaoye
The high defi nition multimedia interface (HDMI) is fastbecoming the de facto standard for passing digitalaudio and video data in home entertainment systems.This standard includes an I2C type bus called a displaydata channel (DDC) that is used to pass extended digitalinterface data (EDID) from the sinkdevice (such as adigital TV) to the source device (such as a digital A/Vreceiver). EDID includes vital information on the digitaldata formats that the sink device can accept. The HDMIspecifi cation requires that devices have less than 50pFof input capacitance on their DDC bus lines, which canbe very diffi cult to meet. The LTC®4300A’s capacitancebuffering feature allows devices to pass the HDMI DDCinput capacitance compliance test with ease.
上传时间： 2013-11-21
上传用户：tian126vip
PQP is a library for performing three types of proximity queries on a pair of geometric models composed of triangles:
标签： performing geometric proximity library
上传时间： 2014-01-13
上传用户：love_stanford
C for Embedded Systems
上传时间： 2013-12-29
上传用户：hxy200501
uClinux on ARM7TDMI(ppt)
上传时间： 2013-12-11
上传用户：shizhanincc
TheTool is highy customizable map editor(based on QT) which can be extended via LUA scripts. A first implentation is ready and can be published to the public. The editor is the perfect tool who wants to design some 3d games but don t have time to write
标签： customizable extended TheTool scripts
上传时间： 2013-12-12
上传用户：lanwei
Displaying a large bitmap file on a dialog box, in its original size, is quite difficult in the VC++ environment. However, it is possible to display a large bitmap to a predefined area of the dialog by using the StretchBlt( ) function.The major disadvantage of this is that the clarity of the image will be lost. Check out this article for displaying large bitmaps into the desired area of your dialog box in its original size with a scrolling technique used to show the entire bitmap. 滚动显示位图 在VC++环境下，在一个对话框中显示一个原始尺寸的大小的位图文件相当是困难的。然而,通过使用 StretchBlt()函数一个给定的区域显示一个大的位图是可能的。主要的缺点是图像将会失真。看了这篇通过卷动技术显示整个位图技术的文章，你将能够以它的原始尺寸在给定对话框的区域内显示一个大位图。 来源: http://www.codeguru.com/bitmap/ScrollBitmap.html
标签： Displaying difficult original bitmap
上传时间： 2014-01-05
上传用户：yiwen213
This article is based in part on Bob Place s ADO is AOK (a simple ADO tutorial). Wrapper Usage This is consist of 2 classes. CDyndb : This Class manages connections and recordsets. Recordsets are organized as linked list (CList) and you can access them using their ids. CDynRec : This class is the node to populate for each recordsets. ADO封装器类 这篇文章一部分基于Bob Place的《ADO is AOK》 (简单的ADO指导) 。 包裹的用法 由2个类组成。 类CDyndb: 这个类别管理连接和记录集。记录集是连接起来的记录的集合，你可以通过他们的ID访问他们。 类CDynRec: 这个类别存放记录集的代码。
上传时间： 2013-12-14
上传用户：wfl_yy
