The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上传时间： 2013-11-16
上传用户：浩子GG
linux 中断和设备驱动 本章介绍L i n u x内核是如何维护它支持的文件系统中的文件的，我们先介绍 V F S ( Vi r t u a lFile System，虚拟文件系统)，再解释一下L i n u x内核的真实文件系统是如何得到支持的。L i n u x的一个最重要特点就是它支持许多不同的文件系统。这使 L i n u x非常灵活，能够与许多其他的操作系统共存。在写这本书的时候， L i n u x共支持1 5种文件系统： e x t、 e x t 2、x i a、 m i n i x、 u m s d o s、 msdos 、v f a t、 p r o c、 s m b、 n c p、 i s o 9 6 6 0、 s y s v、 h p f s、 a ffs 和u f s。无疑随着时间的推移，L i n u x支持的文件系统数还会增加。
上传时间： 2013-11-13
上传用户：zxh122
本文介绍了一种基于单片机的健身车转速测量系统。该系统具有电路简单、使用方便等特点。文中详细介绍了该系统的工作原理,并且给出了它的硬件原理图和软件设计程序框图。关键词:转速 单片机 测量ABSTRACT :This paper introduces a measuring system of the rotational velocity of exercise bike based on single - chip microcomputer . It has such advantages : simple circuit ,convenient use and so on. The work principle is presented in detail in this paper and the block diagram of hardware and program flow chart are giv2 en as well .KEYWORDS :Rotational velocity Single - chip microcomputer Measuring
上传时间： 2013-11-02
上传用户：源弋弋
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
一种实用的微机自动配料秤系统:介绍一种由单片机构成的配料秤。叙述了秤的传感器、变送器、信号的变换、硬件原理、软件流程以及和DCS 系统构成的单回路调节系统,此系统可广泛地应用于各行业的配料控制中。关键词:配料秤 单片机 单回路调节系统 DCS 系统 Abstract :A proportioning weigher based on single chip computer is introduced. Sensors , transmitters , signal converting , principle of hardware ,software flowchart of proportioning weigher and single loop control system composed with DCS system are emphasized ,this system can be used in proportioning control of various trades extensively.Key Words :Proportioning Weigher ,Single Chip Computer ,Single Loop Control System ,Distributed Control System
上传时间： 2013-10-12
上传用户：zwei41
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 Microcontroller Core. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementation of the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision 1.1.This application note describes a demonstration program that has been written for the DK3200 hardware demonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to work with the device, using the HID class as a ready-made device driver for the USB connection.
上传时间： 2014-04-03
上传用户：lizhizheng88
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
