以AT89S52单片机为控制核心,采用电容降压技术,Buck电路拓扑,PWM驱动模块和功率器件散热设计,通过高速的数据采集、主功率输入输出模块和控制模块,设计一种新型智能车载充电器.在充电过程中,通过负脉冲瞬间放电实现对铅酸蓄电池的再生修复,提高电池的有效容量,延长使用寿命.该充电器体积小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat dissipation design,through high-Speed data acquisition,main power input and output module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast Speed,high efficiency and good reliability.
标签： 车载充电器
上传时间： 2022-03-27
上传用户：
数字示波器功能强大,使用方便,但是价格相对昂贵。本文以Ti的MSP430F5529为主控器,以Altera公司的EP2C5T144C8 FPGA器件为逻辑控制部件设计数字示波器。模拟信号经程控放大、整形电路后形成方波信号送至FPGA测频,根据频率值选择采用片上及片外高速AD分段采样。FPGA控制片外AD采样并将数据输入到FIFO模块中缓存,由单片机进行频谱分析。测试表明:简易示波器可以实现自动选档、多采样率采样、高精度测频及频谱分析等功能。Digital oscilloscope is powerful and easy to use, but also expensive. The research group designed a low-cost digital oscilloscope, the chip of MSP430F5529 of TI is chosen as the main controller and the device of EP2C5T144C8 of Altera company is used as the logic control unit. Analog signal enter the programmable amplifier circuit, shaping circuit and other pre-processing circuit. The shaped rectangular wave signal is sent to FPGA for measure the frequency. According to the frequency value to select AD on-chip or off-chip high-Speed AD for sampling. FPGA controls the off-chip AD sampling and buffers AD data by FIFO module. The single chip microcomputer receives the data, and do FFT for spectrum analysis. The test shows that the simple oscilloscope can realize automatic gain selection, sampling at different sampling rates, high precision frequency measurement and spectrum analysis.
上传时间： 2022-03-27
上传用户：
在传统智能小车驱动电路设计中,较多考虑使用直流电机还是步进电机,电机功率、能耗等性能参数。使用具有armCortexM4内核的STM32嵌入式平台控制四轮的4个直流电机。文章基于PWM技术及PID算法,对四轮进行精准地速度、转向及启停控制,实验表明此小车具有优越各种地形适应能力。In the traditional intelligent car drive circuit design,DC motor or stepping motor,motor power,energy consumption and other performance parameters are considered.The four DC motors with four wheels are controlled by STM32 embedded platform with arm Cortex M4 kernel.Based on the PWM technology and PID algorithm,the accurate ground Speed,steering,and start-stop control of the four wheels are carried out.The experiment shows that the vehicle has the superior adaptability to all kinds of terrains.
上传时间： 2022-04-02
上传用户：
本文首次设计并验证了基于macom三合一芯片设计的光模块电路,该电路旨在提供一种满足SFF-8472中规定的数字诊断功能的低成本SFP+模块。电路采用激光器驱动、限幅放大器、控制器以及时钟恢复单元集成的单芯片,在保证高精度数字诊断功能基础上,实现了低成本高可靠的特点。该电路在光接收接口组件与激光器驱动和限幅放大器单元的限幅放大器部分之间接入滤波器来提高模块的灵敏度及信号质量。在控制器单元的数字电位器的引脚上采用外加电阻的方式避免出现上电不发光的故障问题。该研究结果为下一代SFP-DD光模块设计与开发工作,奠定了一定的理论与实践基础。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-Speed data center.
上传时间： 2022-04-03
上传用户：
The GL823K integrates a high Speed 8051 microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and flash card interfaces. Its pin assignment design fits to card sockets to provide easier PCB layout. Inside the chip, it integrates 5V to 3.3V regulator, 3.3V to 1.8V regulator and power MOSFETs and it enables the function of on-chip clock source (OCCS) which means no external 12MHz XTAL is needed and that effectively reduces the total BOM cost.
上传时间： 2022-04-27
上传用户：qdxqdxqdxqdx
基于TMS320F28335的超声波流量计硬件原理图+软件源码本文以TMS320F28335 处理器为核心，设计一种用于管道流量测量的超声波流量计。系统硬件由核心板，超声波发射和接收电路，切换电路，超声换能器，基于ADS805 的高速信号采集电路，人机交互以及电源等模块构成。采用时差法进行管道流量测量，时差测量采用SCOT 加权的广义互相关时延估计算法。本论文设计的超声波流量计具有测量速度快、准确性好、成本低等优点。关键字：C2000，超声波，流量，广义互相关算法AbstractA kind of ultrasonic flowmeter using for the pipe flow measurement is designed based onTMS320F28335 in this paper. The system hardware consists of the following parts: the core board,ultrasonic signal transmitter and receiver circuits, switch circuit, ultrasonic transducer, signalacquisition circuit based on ADS805, human-computer interaction module and power supplymodule, etc. The system use the method of time difference for pipeline flow measurement and thetime difference is calculated by the time-delay algorithm of SCOT weighted generalizedcross-correlation. The ultrasonic flowmeter has the features of high testing Speed, high precisionand low cost, etc.Keywords: C2000,Ultrasonic, Flow, Generalized Cross-Correlation Algorithm
标签： tms320f28335 超声波流量计
上传时间： 2022-05-06
上传用户：
以STM32F103C8T6为核心,设计了无刷直流电机控制器硬件电路。电路主要包括IR2310构成的PWM驱动电路、IRF3808构成的逆变电路、增量式旋转编码构成的速度反馈电路。控制器具有CAN和RS232通信接口,可与计算机或PLC构成速度或位置伺服系统。利用由xPC目标搭建的半实物仿真平台对PI参数进行整定。测试了控制器的速度伺服响应性能,给定速度为2400rpm时,控制器响应时间为0.32s。实验结果表明,系统工作可靠,稳定性好,响应速度快,可以满足上肢康复机器人的机械臂速度控制性能要求。The hardware circuit of Brushless DC motor controller is designed by taking STM32F103C8T6 as the core,which mainly includes PWM driving circuits made up of IR2310,inverter circuit formed by IRF3808,Speed feedback circuit composed of incremental rotary encoder and so on.Speed servo control system or position servo control system can be composed of BLDM controller with computer or PLC through CAN communication interface or RS232 serial communication interface.By using the hardware in the loop simulation platform built by xPC target,the PI parameters are set up.The Speed servo response performance of the controller is tested.When the Speed is 2 400 rpm,the response time of the controller is 0...
上传时间： 2022-05-07
上传用户：
基于DSP28335的永磁同步电机调速系统设计摘要（中英文） 本控制系统的设计是为了实现基于TMS320F28335的永磁同步电动机的调速系统，并把它引用到全电动注塑机当中。本系统使用SVPWM的控制方法，通过采样电机电流和旋转变压器的位置信息，实现速度、电流双闭环控制。通过TMS320F28335的硬件浮点处理核心，实现应用于永磁同步电机的浮点算法，去取代过去的定点算法，提高代码效率。 Abstract: The control system is designed to realize TMS320F28335 based on the permanent magnet synchronous motor Speed control system, and put it to quoting all electric of injection molding machine. The ystem of the control method used SVPWM, through the sampling motor current and rotating transformer 1. 引言1.1 设计背景及目的 本永磁同步电机调速系统是全电动注塑机的其中一个应用部分。全电动注塑机凭借着其节约能源、清洁、噪声少、速度控制效果好、精度高、可重复性高、成本低等众多优点，成为了当下高端注塑机发展的一个方向。 全电动注塑机的所有运动机构都采用交流伺服电动机驱动，一个稳定高效的永磁同步电动机驱动方案成为了全电动注塑机性能的一个总要部分。本次设计以适用于全电动注塑机的永磁同步电动机控制系统为目标进行设计，采用TI公司的TMS320F28335作为控制核心。凭借TMS320F28335高速的运算能力，适用于电动机控制的各种外设，以及TMS320F283XX特有的硬件浮点运算能力，进行永磁同步电动机的调速控制系统的设计。
上传时间： 2022-05-08
上传用户：
基于DSP28035的高速永磁无刷直流电机驱动系统，包括论文和软硬设计资料。摘要参赛作品为基于DSP28035的高速永磁无刷直流电机驱动系统。该系统以一台额定转速60 krpm的高速永磁无刷直流电机、交错并联的Buck电路以及全桥电路为硬件平台，以DSP28035为控制核心，实现了调压调速功能和基于坐标变换的无位置传感器新技术。为实现该系统要求，本作品充分利用了DSP28035的资源例如：CLA模块，模拟比较器、HPWM模块以及AD转换模块等。AbstractThis work is the drive system for a high Speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated Speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s Speed with voltage and the function of sensorless control based on the coordinate transformation. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁无刷直流电机驱动系统由于基波频率较高（一般在1kHZ以上），利用逆变桥斩波进行调速的控制方式通常会受到开关管开关频率的限制，因此该系统多采用三相全桥前级加Buck电路进承担调压调速的功能，而三相全桥主要承担逻辑换相的功能。然而，传统Buck电路所需电感的体积较大，增加了系统的体积，降低了系统的功率密度。
上传时间： 2022-05-08
上传用户：bluedrops
基于TMS320F28035芯片为控制核心的空间矢量异步电机变频器 我们设计的异步电机变频调速器以TMS320F28035芯片为控制核心，通过输出三相PWM波控制智能功率模块IPM驱动三相异步电机。我们使用空间矢量SVPWM算法，并对其进行了优化。采用检测反电势的方法省去了昂贵的光电编码器，大大节省了成本。同时开创性的研发了自动根据运行环境调节的自适应变频算法，使我们的变频调速器可以在电网条件恶劣的乡村山区工作，由此该变频器已被一家民用水泵生产企业预订。关键字 变频器 TMS320f28035 IPM SVPWM In our design, the asynchronous machine inverter based on the chip of TMS320F28035 drives the three-Phase asynchronous machine by sending three-phase PWM waves to the IPM, which is short for the Intelligent-Power-Module. The SVPWM (space vector pulse width modulation) strategy is applied to our control algorithm and we optimize it mainly in two aspects. Firstly the inverter detects the Speed by measuring the Back EMF instead of installing an expensive photoelectric encoder for costs reduction.
标签： tms320f28035 芯片
上传时间： 2022-05-08
上传用户：zhanglei193
