特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 多种输入输出选择（Wide selection of input/output range） 三线式接线自动补偿线路阻抗效应（3 wire configuration automatically compensate line resistance effects） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-17
上传用户：Huge_Brother
产品特点： 全系列加装高速保险丝，防止短路电流（di/dt）对SCR造成损害。 全系列开模成型，体积小、安装、配线容易。 盘面集中多只LED灯头示，遇有状况可立即判断故障原因，迅速排除。 输出特性呈线性，控温最精准。 高品质，高技术产品，绝无干扰现象，加装透明护盖，安全性增加。 独具Soft Start（缓启动）功能，可避免大电流启动。 具有保险丝熔断、电源异常、SCR超温指示及异常接点输出。 内含电子式自动温度侦测器作为散热器超温保护。 冷却风扇全自动控制，温度过高时风扇运转，避免风扇长时间运转，延长风扇寿命。
上传时间： 2013-10-10
上传用户：ouyang426
特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 宽输入范围200ohm 至 50Kohm（Wide inpuet ranges from 200ohm to 50Kohm） 多种输入输出选择（Wide selection of input/output range） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-28
上传用户：sardinescn
特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 多种输入输出选择（Wide selection of input/output range） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2014-12-24
上传用户：qimingxing130
特点（FEATURES） 精确度0.03%满刻度（Accuracy 0.03%F.S.） 频率输入范围0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔离类比输出（16 bit DAC isolating analog output） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-21
上传用户：dljwq
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上传时间： 2013-10-23
上传用户：wuchunzhong
