The acceptance and introduction of serial communication to more and more applications has led to requirements that the assignment of message identifiers to communication functions be standardized for certain applications. These applications can be realized with CAN more comfortably, if the address range that originally has been defined by 11 identifier bits is enlarged
标签： more communication introduction applications
上传时间： 2014-01-04
上传用户：小草123
TC35i新版西门子工业GSM模块是一个支持中文短信息的工业级GSM模块,工作在EGSM900和GSM1800双频段,电源范围为直流3.3～4.8V ,电流消耗——休眠状态为3.5mA，空闲状态为25mA，发射状态为300mA(平均)，2.5A峰值；可传输语音和数据信号, 功耗在EGSM900(4类)和GSM1800(1类)分别为2W和1W ,通过接口连接器和天线连接器分别连接SIM卡读卡器和天线。SIM电压为3V/1.8V，TC35i的数据接口(CMOS电平)通过AT命令可双向传输指令和数据,可选波特率为300b/s～115kb/s , 自动波特率为1.2kb/s～115kb/s。它支持Text和PDU格式的SMS(Short Message Service,短消息),可通过AT命令或关断信号实现重启和故障恢复
上传时间： 2016-08-26
上传用户：fnhhs
gps matlab 仿真程序（A collection of geodetic functions that solve a variety of problems in geodesy. Supports a wide range of common and user-defined reference ellipsoids. Most functions are vectorized.）
标签： collection functions geodetic problems
上传时间： 2014-12-07
上传用户：whenfly
RECOMMENDATION ITU-R M.1653*,** Operational and deployment requirements for wireless access systems including radio local area networks in the mobile service to facilitate sharing between these systems and systems in the Earth exploration-satellite service (active) and the space research service (active) in the band 5 470-5 570 MHz within the 5 460 5 725 MHz range
标签： RECOMMENDATION requirements Operational deployment
上传时间： 2016-10-21
上传用户：miaochun888
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2013-12-13
上传用户：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2014-01-20
上传用户：三人用菜
短信发送实现gprs猫发送短信息，wap push，push load，免提短信源代码.-gprs cat achieve this short message, WAP push, push load. Handsfree SMS source code
上传时间： 2014-01-21
上传用户：cooran
Produce Java classes to calculate and display the root of a quadratic equation when input the coefficients a, b and c within the range of -100 to 100 by user.
标签： calculate the quadratic equation
上传时间： 2014-01-17
上传用户：aappkkee
Produce Java classes to calculate and display the Poisson probability when input the value of the average (A) arrival rate of customers at some business in the range of 1 to 10. The error message will output when A is out of the range。
标签： the probability calculate Produce
上传时间： 2014-01-10
上传用户：moerwang
This GUI can be used by entering nu at the MATLAB command prompt. The user can either select a function (f(x)) of their choice or a statistical distribution probability distribution function to plot over a user defined range. The function s integral can be evaluated over a user defined range by using: The composite trapezium, simpsons and gauss-legendre rules. This is useful for calculating accurate probabilities that one might see in statistical tables.
标签： can entering command MATLAB
上传时间： 2016-11-07
上传用户：偷心的海盗
