以C8051F020为核心处理器，设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络，结合嵌入式系统的软硬件技术，完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后，分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据，通过Zigbee无线网络传送到上位机，系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签： C8051F020 Zigbee 汽车测试 系统设计
上传时间： 2013-11-23
上传用户：dsgkjgkjg
阐述了一个由上位PC机和AT89C52下位单片机组成的主从分布式温度巡回检测系统。主从机采用RS-485 串行通讯标准进行通信，可在下位单片机实现基本的温度数据巡回检测基础上，由上位PC机实现综合处理功能或扩展为远程操作。整个系统具有巡检速度快，扩展性好的特点。 Abstract: In this paper,a top PC and AT89C52 under-bit microcontrollers from the main component of the tour distributed temperature detection system is presented. Master and slave can use RS-485 serial communication standards for communications.Based on next-bit machine for basic goods temperature detected data Tour, the top can achieve the integrated treatment of PC functions or for the expansion of long-distance operation. The entire inspection system is fast, expansion.
上传时间： 2013-10-13
上传用户：zhoujunzhen
介绍一种无极可调交流电子负载设计的新方法，由ATmega48单片机输出PWM波，通过上位机设定不同的占空比控制场效应管的通断时间，即改变流过场效应管的平均电流。根据电流的大小，可以等效为相应的负载，并将采集的电流值显示在上位机上。文中对该系统的软﹑硬件设计思路作了详细的分析，阐述了其设计原理。 Abstract: A new type electronic load is introduced.Due to ATmega48 microcomputer output PWM wave.The different duty is set ratio through PC to control FET turn-on time.We can equivalent homologous load according the current and display the current at PC.The hardware and software designing are analysed in detail. The principle is explained and the output is also given.
上传时间： 2013-11-23
上传用户：虫虫虫虫虫虫
介绍以P87LPC764型单片机为核心的延时型漏电继电器设计方案。该方案可供用户选择实现额定动作电流和5倍额定动作电流下不同的延时动作时间，并有重合闸设定选择功能。解决了以往传统分立元件带来的延时时间离散性大且不易实现的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上传时间： 2013-11-08
上传用户：zhaiye
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
上传时间： 2013-10-23
上传用户：顶得柱
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上传时间： 2013-11-08
上传用户：laozhanshi111
The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
本文以PIC24FJ64GA002 16位单片机为处理器控制10BASE-T SPI以太网控制器ENC28J60，实现了单片机的上网。应用Microchip TCPIP Stack协议,实现了HTTP,FTP协议和基于CGI动态网页的设计。操作员可以在远程计算机上以Web页面的方式实现系统的监控，也可以通过FTP更新系统参数和数据。最后将本系统应用在了生物发酵远程监控系统中，得到了良好的效果。
上传时间： 2013-11-08
上传用户：赵一霞a
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
