虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

STM32-DMA-USART<b>学习笔记</b>

  • 2012TI杯陕西赛题B题--频率补偿电路

    2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.

    标签: 2012 TI 频率补偿电路

    上传时间: 2013-10-07

    上传用户:ysystc670

  • 飞思卡尔的PCB布局布线应用笔记,很值得学习的

    飞思卡尔的PCB布局布线应用笔记,很值得学习的

    标签: PCB 飞思卡尔 布局布线 应用笔记

    上传时间: 2013-11-14

    上传用户:elinuxzj

  • STM32自学笔记

    STM32自学笔记

    标签: STM 32

    上传时间: 2013-10-12

    上传用户:450976175

  • PSHLY-B回路电阻测试仪

    PSHLY-B回路电阻测试仪介绍

    标签: PSHLY-B 回路 电阻测试仪

    上传时间: 2013-11-05

    上传用户:木子叶1

  • 基于单片机的数字化B超键盘设计

    针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS,提出一种PS2键盘的设计方法。基于W78E052D单片机,采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路,电位器位置信息以键盘扫描码序列形式发送,正交编码器信号通过XC9536XL转换为单片机可接收的中断信号,软件接收到中断信息后等效处理成按键。结果表明,在满足开机可设置BIOS同时,又可实现超声特有功能,不需要专门设计驱动程序,接口简单,成本低。 Abstract:  Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot, this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller,designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter, potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU, software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot, ultrasound specific functionality can be achieved at the same time, it does not require specially designed driver,the interface is simple and low cost.    

    标签: 单片机 B超 数字化 键盘设计

    上传时间: 2013-10-10

    上传用户:asdfasdfd

  • keil使用笔记

    keil 使用笔记:在Memory窗口上输入address_type:address才能看到正确地址的变量debug~perfermance analyzer加入要察看的模块名称,然后view~perfermance analyzer window 可以察看各个模块运行时间①Display address_type:address B:Bit address C:Code Memory Bx:Code Bank D D:80H 命令可以查看特殊寄存器 data D I:0 命令可以查看内部RAM数据iData; D X:0 命令可以查看外部RAM数据xData; ②R1 //显示R1 register ~R1 //显示变量R1 R1 = R7 //对寄存器Rx操作R1 = --R7 R1 = 0x20 ③main //显示main()的开始地址d main //显示main()的代码④向RAM.ROM中写数据Enter data_type address_type:address expr,expr.... data_type:int char double float long E char data:0x20 1,2,3,4 //向data区0x20开始的地址写1,2,3,4 变量放在RAM的30H,要把定义放在main前面!另外特别注意,内部RAM通常供C程序存放中间变量等,所以一定要看看编译后的程序中是否存在存储单元冲突的情况,比如如果程序中 使用了别的寄存器组的话,08-1FH单元就不能用了unsigned long data i _at_ 0x30

    标签: keil 使用笔记

    上传时间: 2013-11-05

    上传用户:dongqiangqiang

  • TKS仿真器B系列快速入门

    TKS仿真器B系列快速入门

    标签: TKS 仿真器 快速入门

    上传时间: 2013-10-31

    上传用户:aix008

  • 1 芯嵌STM32入门教程之一《如何提高STM32的学习效率》

    芯嵌stm32开发板配套的教程之一《如何提高STM32的学习效率》

    标签: STM 32 入门教程 如何提高

    上传时间: 2013-10-16

    上传用户:csgcd001

  • STM32之DMA

    STM32之DMA视频

    标签: STM DMA 32

    上传时间: 2013-11-13

    上传用户:leixinzhuo

  • 学习stm32定时器

    学习stm32定时器

    标签: stm 32 定时器

    上传时间: 2013-10-31

    上传用户:miaochun888