This program accesses a SPI EEPROM using polled mode access. The F12x MCU is configured in 4-wire Single Master Mode, and the EEPROM is the only slave device connected to the SPI bus. The read/write operations are tailored to access a Microchip 4 kB EEPROM
标签： configured accesses program EEPROM
上传时间： 2016-03-29
上传用户：gut1234567
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
标签： configured accesses program EEPROM
上传时间： 2014-01-18
上传用户：liglechongchong
// This program accesses a SPI EEPROM using polled mode access. The F06x MCU // is configured in 4-wire Single Master Mode, and the EEPROM is the only // slave device connected to the SPI bus. The read/write operations are // tailored to access a Microchip 4 kB EEPROM 25LC320. The relevant hardware // connections of the F06x MCU are shown here:
标签： configured accesses program EEPROM
上传时间： 2016-04-12
上传用户：qb1993225
练习并掌握多任务实时操作系统下Task 调度、Task 间主要通信手段（信号量、消息队列等）、RISC 处理器 I/O 端口控制等内容，并形成嵌入式实时应用软件的良好编程习惯。创建多Task，为每个Task 创建私有的Message Queue，每个Task 只通过自己的私有Message Queue 接收消息；Task 间消息通信通过向对方私有MessageQueue 发送消息完成。 Task1：管理Task。负责系统启动时同步系统中其他Task 的启动同步，利用信号量的semFlush()完成。同时接收各Task 的告警信息，告警信息需编号以logmsg 方式输出。本task 负责系统结束时的Task 删除处理。 Task2：console 命令行接收Task。接收并分析console 发来的命令行及参数。自行设置5 种以上命令，并根据命令的内容向Task3 或/及Task4 发送激励消息。同时实现系统退出命令，使系统采用适当方式安全退出。收到非法命令向Task1告警。 Task3：Led 控制Task。接收Led 控制消息（命令），自定义Led 显示方式表现命令执行情况。本task 应负责led 相关I/O port 初始化。收到非法led 控制命令向Task1 告警。 Task4：console 输出Task。接收需打印输出的字串消息（命令），输出到console。收到长度为0 或超常字串向Task1 告警。
上传时间： 2016-04-12
上传用户：iswlkje
C8051程序， writes text to the serial port of the 8052，用keil编译
上传时间： 2016-04-15
上传用户：牛布牛
This manual describes Freescale’s IEEE™ 802.15.4 Standard compliant MAC/PHY software. The Freescale 802.15.4 MAC/PHY software is designed for use with the Freescale MC1319x and MC1320x, family of short range, low power, 2.4 GHz Industrial, Scientific, and Medical (ISM) band transceivers, designed for use with the HCS08 Family of MCUs. The MAC/PHY software also works with the MC1321x family of short range, low power, 2.4 GHz ISM band transceivers that incorporate a low power 2.4 GHz radio frequency transceiver and an 8-bit microcontroller into a single LGA package. Throughout this manual, the term transceiver refers to either the MC1319x, MC1320x, or the internal counterpart inside the MC1321x System in a Package (SiP).
标签： Freescale describes compliant Standard
上传时间： 2016-04-17
上传用户：caiiicc
This little Program allows you to send commands to the CardReader (CT-BCS) or to the Card itself. First you will be ask to what Port the Reader is connected (0=COM1, 1=COM2). Then the Class-Byte (CLA), Instruction-Byte (INS), Parameter 1 (P1), Parameter 2 (P2). If wou don愒 want to send Parameter 3 (P3) press Ctrl-d (^d). If you enter a number then you have to the Bytes of the Datafield. After the last Byte of the Datafield is entered the whole APDU is send the replay is displayed. After that you can send the next APDU.
标签： CardReader the commands to
上传时间： 2016-04-23
上传用户：nanxia
This will sample all 8 A/D-channels by the continous mode. Each end of conversion will call an interrupt routine, where the AD-channel is put to Port4[2..0] and the upper nibble of the result is put to Port4[7..4]. Port 4 is connected to the user LEDs of the FlashCan100P Evaluation-Board
标签： will D-channels conversion continous
上传时间： 2013-12-09
上传用户：zm7516678
富士通单片机MB902420系列 CAN Project: CAN0 will work as a simple Repeater. Received data will appear at Port P47..P40 (UserLEDs of FlashCan100P) and will send out again as byte-packages to ID#2 Receive-Buffer #1 : basic can Transmit-Buffer #6 : full-can ID #2
标签： will Repeater Received Project
上传时间： 2016-04-27
上传用户：www240697738
The neuro-fuzzy software for identification and data analysis has been implemented in the MATLAB language ver. 4.2. The software trains a fuzzy architecture, inspired to Takagi-Sugeno approach, on the basis of a training set of N (single) output-(multi) input samples. The returned model has the form 1) if input1 is A11 and input 2 is A12 then output =f1(input1,input2) 2) if input1 is A21 and input 2 is A22 then output =f2(input1,input2) 看不懂，据高手说，非常有用。
标签： identification neuro-fuzzy implemented analysis
上传时间： 2014-01-12
上传用户：zgu489
