电感型DC-DC转换器电路，闭合开关会引起通过电感的电流增加。打开开关会促使电流通过二极管流向输出电容。因储存来自电感的电流，多个开关周期以后输出电容的电压升高，结果输出电压高于输入电压。
上传时间： 2013-11-22
上传用户：上善若水
随着通信信道的复杂度和可靠性不断增加，人们对于电信系统的要求和期望也不断提高。这些通信系统高度依赖于高性能、高时钟频率和数据转换器器 件，而这些器件的性能又非常依赖于系统电源轨的质量。当使用一个高噪声电源供电时，时钟或者转换器 IC 无法达到最高性能。仅仅只是少量的电源噪声，便会对性能产生极大的负面影响。本文将对一种基本 LDO 拓扑进行仔细研究，找出其主要噪声源，并给出最小化其输出噪声的一些方法。 表明电源品质的一个关键参数是其噪声输出，它常见的参考值为 RMS 噪声测量或者频谱噪声密度。为了获得最低 RMS 噪声或者最佳频谱噪声特性，线性电压稳压器（例如：低压降电压稳压器，LDO），始终比开关式稳压器有优势。这让其成为噪声敏感型应用的选择。 基本 LDO 拓扑 一个简单的线性电压稳压器包含一个基本控制环路，其负反馈与内部参考比较，以提供恒定电压—与输入电压、温度或者负载电流的变化或者扰动无关。 图 1 显示了一个 LDO 稳压器的基本结构图。红色箭头表示负反馈信号通路。输出电压 VOUT 通过反馈电阻 R1 和 R2 分压，以提供反馈电压 VFB。VFB 与误差放大器负输入端的参考电压 VREF 比较，提供栅极驱动电压 VGATE。最后，误差信号驱动输出晶体管 NFET，以对 VOUT 进行调节。 图 1 LDO 负反馈环路 简单噪声分析以图 2 作为开始。蓝色箭头表示由常见放大器差异代表的环路子集（电压跟随器或者功率缓冲器）。这种电压跟随器电路迫使 VOUT 跟随 VREF。VFB 为误差信号，其参考 VREF。在稳定状态下，VOUT 大于 VREF，其如方程式 1 所描述：
上传时间： 2013-11-11
上传用户：jiwy
Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
上传时间： 2013-10-26
上传用户：lyson
描述了一种简易的交流数字电压表的系统设计。系统以MSP430F448为核心，该单片机内部集成了12位的A/D转换器，转换器带有内部参考源、采样保持、自动扫描特性，极大地简化了硬件设计。
上传时间： 2014-12-22
上传用户：cuibaigao
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
便携式电子器件(如智能手机、GPS导航系统和平板电脑)的电源可以来自低压太阳能电池板、电池或AC/DC电源。电池供电系统通常将电池串联叠置以实现更高的电压，但由于空间不足，此技术未必总是可行。开关转换器使用电感的磁场来交替地存储电能，并以不同电压释放至负载。因为损耗很低，所以开关转换器是个不错的高效率选择。连接至转换器输出端的电容可减少输出电压纹波。升压转换器提供较高的输出电压；而应用笔记AN-1125(如何运用DC-DC降压调节器)所讨论的降压转换器则提供较低的输出电压。内置FET作为开关的开关转换器称为开关调节器，需要外部FET的开关转换器则称为开关控制器。
上传时间： 2013-11-04
上传用户：edisonfather
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Low power standby requirements are typically associatedwith battery-powered systems. Automotive systems,for example, commonly require power supplies tomaintain output voltage regulation even under no-loadconditions—while drawing minimal quiescent current topreserve battery life. Rising energy costs, however, haveextended the need for low current standby operation toline-powered systems, such as small plugged-in appliancesfor home and business.
上传时间： 2013-11-20
上传用户：xinyuzhiqiwuwu
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Typical industrial and automotive applications requiremultiple high current, low voltage power supply solutionsto drive everything from disc drives to microprocessors.For many of these applications, particularly thosethat have size constraints, the LT3501® dual step-downconverter is an attractive solution because it’s compactand inexpensive compared to a 2-chip solution. The dualconverter accommodates a 3V to 25V input voltage rangeand is capable of supplying up to 3A per channel. Thecircuit in Figure 1 produces 3.3V and 1.8V.
上传时间： 2014-12-24
上传用户：372825274
