The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
基于PIC单片机的脉冲电源:设计了一种金属凝固过程用脉冲电源。该电源采用PIC16F877作为主控芯片，实现对窄脉冲电流幅值的检测，以及时电流脉冲幅值根据模糊PID算法进行闲环控制。使用结果表明：该电源的输出脉冲波形良好，电流幅值稳定，满足合金材料凝固过程的工艺要求且运行稳定可靠。关键词：脉冲电源；PIC16F877单片机；模糊PID；闲环控制 Abstract：A kind of pulse power supply was designed which uses in the metal solidification process ．．I11is power supply used PIC16F877 to take the master control chip reali on to the narrow pulse electric current peak-to-peak value examination，carried on the closed-loop control to the electric current pulse peak-to-peak value basis fuzzy PID algorithm．The use result indicated ，this power supply output se profile is good，and the electric current peak-to-p~k value is stable，It satisfies the alloy material solidification process the technological requirement and movement stable reliable，Key words：p se po wer supply；PIC16F877single-chip microcontroller；f r PID；closed-loop control
上传时间： 2013-10-27
上传用户：xcy122677
多功能高集成外围器件6. 1 多功能高集成外围器件82371PCI的英文名称：Peripheral Component Interconnect （外围部件互联PCI总线）；82371是PCI总线组件。ISA是：Industry Standard Architecture（工业标准体系结构）IDE是 （Integrated Device Electronics）集成电路设备简称PIIX4PIIX4器件（芯片）的特点1、是一种支持Pentium和PentiumII微处理器的部件。2、82371对ISA桥来说，是一种多功能PCI总线。3、对可移动性和桌面深绿色环境均提供支持。4、电源管理逻辑。5、被集成化的IDE控制器。6、增强了性能的DMA控制器。 （7）基于两个82C59的中断控制器。（8）基于82C54芯片的定时器。（9）USB（Universal Serial Bus）通用串行总线。（10）SMBus系统管理总线。（11）实时时钟（12）顺应Microsoft Win95所需的功能其芯片的逻辑框图如图6-1所示。 PIIX4芯片逻辑框图6.1.1 概述PIIX4芯片是一个多功能的PCI器件，图6-2 是82371在系统中扮演的角色。（续上图）1. PCI与EIO之间的桥（PIIX4芯片）桥是不对程的，是各类不同标准总线与PCI总线连接，82371AB桥也可理解为一种总线转换译码器和控制器，桥内包含复杂的协议总线信号和缓冲器。(1).在PCI系统内，当PIIX4操作时，它总是作为系统内各种模块的主控设备，如USB和DMA控制器、IDE总线和分布式DMA的主控设备等，而且总是以ISA主控设备的名义出现。(2). 在向ISA总线或IDE总线进行传送操作的传送周期期间作为从属设备使用，并对内部寄存器译码。PIIX4芯片（桥）的配置(1).可以把PIIX4芯片配置成整个ISA总线，或ISA总线的子集，也可扩展成EIO总线。在使用EIO总线时，可以把未使用的信号配置成通用的输入和输出。(2).PIIX4可直接驱动5个ISA插槽；(3).能提供字节-交换逻辑、I/O的恢复支持、等待状态的生成以及SYSCLK的生成。(4).提供X-BUS键盘控制器芯片、BIOS芯片、实时时钟芯片、二级微程序器等的选择。2. IDE接口（总线主控设备的权利和同步DMA方式）IDE接口为4个IDE的设备提供支持，比如IDE接口的硬盘和CD-ROM等。注意：目前硬盘接口有5类：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口几乎在PC机最多，因为便宜。SCSI多用于服务器和集群机。IDE的PIO IDE速率：14MB/s；而总线主控设备IDE的速率：33MB/s在PIIX4芯片的IDE系统内，配有两个各次独立的IDE信号通道。3. 具有兼容性的模块—DMA、定时器/计数器、中断控制器等（1）在PIIX4内的两各82C37 DMA控制器经逻辑的组合，产生7个独立的可编程通道。通道[0：3]是通过与8个二进位的硬件连线实现的。通过以字节为单位的计数进行传送。而通道[5：7]是通过16个二进位的连线实现的，以字为单位的计数进行传送。（2）DMA控制器还能通过PCI总线，处理旧的DMA的两个不同的方法提供支持。（3）计数/定时器模块在功能上与82C54等价。（4）中断控制器与ISA兼容，其功能是两个82C59的功能之和。
上传时间： 2013-11-19
上传用户：3到15
82C59A-2是为简化微处理机系统中断接口而实现的LSI外围芯片。也叫做PIC（Programmable Interrupt Controller）。是高性能高速度芯片。在多级优先级中断系统内82C59A-1402已经把CPU从对任务的轮询中解救出来。PCI可由软件进行控制，使用于各种不同的环境，联级可接受8~64个中断输入。 管脚与NMOS8259A-2兼容单片8级优先级，级联可扩64级多种可编程中断方式各自专用的请求屏蔽能力与Intel系列机兼容全部采用静态设计低功耗5V的电源供电。
上传时间： 2013-10-30
上传用户：zhliu007
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上传时间： 2013-11-02
上传用户：zw380105939
The 87LPC76X Microcontroller combines in a small package thebenefits of a high-performance microcontroller with on-boardhardware supporting the Inter-Integrated Circuit (I2C) bus interface.The 87LPC76X can be programmed both as an I2C bus master, aslave, or both. An overview of the I2C bus and description of the bussupport hardware in the 87LPC76X microcontrollers appears inapplication note AN464, Using the 87LPC76X Microcontroller as anI2C Bus Master. That application note includes a programmingexample, demonstrating a bus-master code. Here we show anexample of programming the microcontroller as an I2C slave.The code listing demonstrates communications routines for the87LPC76X as a slave on the I2C bus. It compliments the program inAN464 which demonstrates the 87LPC76X as an I2C bus master.One may demonstrate two 87LPC76X devices communicating witheach other on the I2C bus, using the AN464 code in one, and theprogram presented here in the other. The examples presented hereand in AN464 allow the 87LPC76X to be either a master or a slave,but not both. Switching between master and slave roles in amultimaster environment is described in application note AN435.The software for a slave on the bus is relatively simple, as theprocessor plays a relatively passive role. It does not initiate bustransfers on its own, but responds to a master initiating thecommunications. This is true whether the slave receives or transmitsdata—transmission takes place only as a response to a busmaster’s request. The slave does not have to worry about arbitrationor about devices which do not acknowledge their address. As theslave is not supposed to take control of the bus, we do not demandit to resolve bus exceptions or “hangups”. If the bus becomesinactive the processor simply withdraws, not interfering with themaster (or masters) on the bus which should (hopefully) try toresolve the situation.
上传时间： 2013-11-19
上传用户：shirleyYim
