针对TI公司最新发布的TMS320C6678 DSP设计出一种实用有效的电源。采用统一的12 V电源供电，制作出满足电压幅值要求与时序要求的开关电源。该设计主要由各类电源转换电路组成，并通过使用Fusion Digital Power Designer软件对电源芯片进行编程。仿真结果表明，该电源工作稳定，各方面的参数均符合要求。
上传时间： 2013-10-12
上传用户：asdstation
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
有源功率因数校正可减少用电设备对电网的谐波污染，提高电器设备输入端的功率因数。详细分析了有源功率因数校正APFC（active power factor corrector）原理，采用平均电流控制模式控制原理，设计了基于UC3854BN芯片的一种有源功率因数校正电路方案，着重分析了电路主要参数的选择和设计。实践证明，采用APFC后，大大减小了输入电流的谐波分量，实现了功率因数校正。
上传时间： 2013-10-21
上传用户：immanuel2006
内涵PCB及其原理图（原PCB为crazyboye所制，Gavin尽量把双面改一面，因为学校没有制版机）
上传时间： 2013-11-24
上传用户：674635689
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
上海晶丰明源半导体有限公司(Bright Power Semiconductor ) 是一家从事电源管理芯片设计和销售的公司，公司主要产品是大功率LED驱动芯片.
上传时间： 2013-10-16
上传用户：aysyzxzm
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
This document presents design techniques and reference circuits that power Virtex™-4 FXRocketIO™ multi-gigabit transceivers (MGTs) operating at data rates below 3.125 Gb/s.When using multiple transceivers, it is sometimes preferred to power them from a switchingpower supply. However, switching power supplies generate noise that affects transceiver
上传时间： 2013-11-18
上传用户：huang111
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
Abstract: It is critically important that lithium-ion battery stacks have a good battery-management system for monitoring many cellvoltages and cell temperatures. Without that monitoring, thermal runaway can lead to a battery explosion. This design idea presentsa low-power circuit that measures the temperature of up to 12 thermistors. It powers and configures the multiplexers, and also putsthe muxes into shutdown to save power when not measuring temperatures.
上传时间： 2013-10-29
上传用户：xwd2010
