OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
PCB 设计完成，通常需要导出gerber 文件提供给PCB 加工厂，编写本教程的目的是为了
上传时间： 2013-11-20
上传用户：cc1015285075
制作此教程的目的旨在学习， 网上也有很多讲的比较好的教程，此做并不是想跟他们比什么，希望此教程能对大家学习有所帮助。每个教程讲的内容不尽相同，希望此教程能够帮助大家快速学习Alitum Designer、PADS 和Cadence。
上传时间： 2014-01-14
上传用户：q986086481
PowerP Router教程
上传时间： 2013-10-11
上传用户：开怀常笑
有时候，做元件封装的时候，做得不是按中心设置为原点（不提倡这种做法），所以制成之后导出来的坐标图和直接提供给贴片厂的要求相差比较大。比如，以元件的某一个pin 脚作为元件的原点，明显就有问题，直接修改封装的话，PCB又的重新调整。所以想到一个方法：把每个元件所有的管脚的X坐标和Y坐标分别求平均值，就为元件的中心。
上传时间： 2013-11-01
上传用户：ccccccc
PADS_LAYOUT_入门教程.ppt
上传时间： 2013-10-27
上传用户：lbbyxmraon
挺好的
上传时间： 2013-11-09
上传用户：bruce
绝对的管用
上传时间： 2013-11-05
上传用户：liu999666
好东东
上传时间： 2013-11-25
上传用户：元宵汉堡包
