Boost LED drivers are often used to drive LEDs in series. If an LED fails while open,Overvoltage protection (OVP) is necessary to avoid the damage to a boost integrated circuit (IC) or output capacitor. This application report presents the solutions to increase the TPS61043 LED driver OVP threshold.
标签： Overvoltage Protection Solutions Driver
上传时间： 2013-10-14
上传用户：jiangfire
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,Overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and Overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
FFeeaattuurreess Input voltage range: 2.2 to 6V Programmable LED Current Drives LEDs Up to 27V Switching Frequency：up to 800KHz Wide dimming frequency range: 20KHz~ 360 KHz Programmable Overvoltage Protection Tiny SOP8/PP Package
标签： HX3248C
上传时间： 2021-11-05
上传用户：aben
CHAPTER 1: THE OP AMP CHAPTER 2: OTHER LINEAR CIRCUITS CHAPTER 3: SENSORS CHAPTER 4: RF/IF CIRCUITS CHAPTER 5: FUNDAMENTALS OF SAMPLED DATA SYSTEMS CHAPTER 6: CONVERTERS CHAPTER 7: DATA CONVERTER SUPPORT CIRCUITS CHAPTER 8: ANALOG FILTERS CHAPTER 9: POWER MANAGEMENT CHAPTER 10: PASSIVE COMPONENTS CHAPTER 11: Overvoltage EFFECTS ON ANALOG INTEGRATED CIRCUITS CHAPTER 12: PRINTED CIRCUIT BOARD (PCB) DESIGN ISSUES CHAPTER 13: DESIGN DEVELOPMENT TOOLS
上传时间： 2021-12-21
上传用户：wangshoupeng199
The PW2601 is a charger front-end integrated circuit designed to provide protection to Li-ionbatteries from failures of charging circuitry. The device monitors the input voltage, battery voltageand the charging current to make sure all three parameters are operated in normal range. Thedevice will switch off internal MOSFET to disconnect IN to OUT to protect load when any of inputvoltage, output current exceeds the threshold. The Over temperature protection (OTP) functionmonitors chip temperature to protect the device. The PW2601 also can protect the system’sbattery from being over charged by monitors the battery voltage continuously. The deviceoperates like a linear regulator, maintaining a 5.1V output with input voltages up to the input Overvoltage threshold.The PW2601 is available in DFN-2x2-8L package. Standard products are Pb-free and Halogenfree
标签： pw2601
上传时间： 2022-02-11
上传用户：
锂电池BMS管理技术是移动机器人的关键技术,本文设计了基于bq76PL455、STM32F103的锂电池管理系统,实现了电池组电压、电流、过压、过流等状态监测;系统配置均衡电路,电池充电过程中若出现电池单体电压不平衡现象,会触发均衡电路,进而提高电池的安全性,延长使用寿命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the monitoring of battery pack voltage,current,Overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上传时间： 2022-04-02
上传用户：
