在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
生成BCD码。 Name: BIN3toBCD4 Func:2字节二进制整数--->>BCD码四字节转换(Comped BCD) Input: 3进制数人低字节到高字节存放在内部RAM50H，51H,52h单元中 Output: BCD码人低位到高位分别存放在内部RAM53H,54H，55H，56H单元中 USE: R7-R0, 56H-50H
标签： BCD BIN3toBCD4 Comped Input
上传时间： 2015-02-02
上传用户：FreeSky
对c语言的简单语法分析器 文件说明： input.txt内为输入的源程序，包括for，while和if else控制等 output.txt内为输出的二元单词序列 k.txt为关键字表 l.txt为运算符和界符表 i.txt为该输入的源程序的标志符 c.txt为常数表 个别表需要序列号，这时各表的序列号默认为从1开始，每行加1。 使用说明： 在提示符下输入input.txt文件的路径和文件名字， 运行完成后，打开文件output.txt看结果。
上传时间： 2013-12-23
上传用户：pompey
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
标签： multiplication Implement matrices matrix
上传时间： 2014-08-30
上传用户：dsgkjgkjg
* * Input * bin_data : binary data * bin_size : binary data length * Mode : operation mode * BASE64_NeedCRLF ---- Need a CRLF every 64 base64-character * BASE64_NotCRLF ---- Need not CRLF between 64 base64-character * * Output * char data * char data length * * Return * 0: success -1: error
标签： binary data operation bin_data
上传时间： 2015-06-04
上传用户：ZJX5201314
Routine mampres: To obtain amplitude response from h(exp(jw)). input parameters: h :n dimensioned complex array. the frequency response is stored in h(0) to h(n-1). n :the dimension of h and amp. fs :sampling frequency (Hz). iamp:If iamp=0: The Amplitude Res. amp(k)=abs(h(k)) If iamp=1: The Amplitude Res. amp(k)=20.*alog10(abs(h(k))). output parameters: amp :n dimensioned real array. the amplitude-frequency response is stored in amp(0) to amp(n-1). Note: this program will generate a data file "filename.dat" . in chapter 2
标签： dimensione parameters amplitude response
上传时间： 2013-12-19
上传用户：xfbs821
Routine mar1psd: To compute the power spectum by AR-model parameters. Input parameters: ip : AR model order (integer) ep : White noise variance of model input (real) ts : Sample interval in seconds (real) a : Complex array of AR parameters a(0) to a(ip) Output parameters: psdr : Real array of power spectral density values psdi : Real work array in chapter 12
标签： parameters AR-model Routine mar1psd
上传时间： 2015-06-09
上传用户：playboys0
对读入的某个文本文件input.txt中，拆出英文单词，输出一个按字典顺序排列的单词表，结果输出在文本文件output.txt中，每个单词一行，并在单词后输出该单词出现的个数，两个字段之间用逗号分隔。约定单词仅由英文字母组成，单词间由非英文字母分隔，相同单词只输出一个，大小写不区分。 利用二叉树实现
上传时间： 2015-07-04
上传用户：yulg
h.263 c编码源码。目录下有input。qcif原始未压缩文件，运行程序生成重建文件recon。qcif和压缩后文件output。263文件。
上传时间： 2013-12-19
上传用户：ljmwh2000
工程计算MATLAB code to calculate the reorthogonalized sine tapers input: N = the length of the time series data to be tapered p = the number of tapers requested I = the gap structure a vector of length N I(t) = 1 if there is data at time t, t=1, ..., N I(t) = 0 if there is a gap at time t output: X = N-by-p vector of the reorthogonalized sine taper
标签： the reorthogonalized calculate MATLAB
上传时间： 2013-12-17
上传用户：wangyi39
