LLCR Pin Socket Testing with the Model 3732 High Density Matrix Card Computer processors (CPUs) today have come a long way from the computer processors of the past. They draw More power, run at lower voltages, and have More pins than ever before.
上传时间： 2013-10-24
上传用户：whenfly
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much More.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [via macros]• Trace visualisation ability (requires More RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
上传时间： 2013-10-13
上传用户：13162218709
The Controller Area Network (CAN) is a serial, asynchronous, multi-master communication protocol forconnecting electronic control modules, sensors and actuators in automotive and industrial applications.With the SJA1000, Philips Semiconductors provides a stand-alone CAN controller which is More than a simpleeplacement of the PCA82C200.Attractive features are implemented for a wide range of applications, supporting system optimization, diagnosisand maintenance.
标签： Stand-alone contro 1000 SJA
上传时间： 2013-11-18
上传用户：yxgi5
<Almost since the introduction of microcontrollers as electronic components there always has been an oscillatorcircuit on the device to make it work. From application point of view only some external components wererequired to make it work. However, to make sure that it will always work required More effort. This report is basedon feedback from the market from customers applying 8-bit mircrocontrollers.>
标签： oscillators X-tal bit mic
上传时间： 2013-11-12
上传用户：穿着衣服的大卫
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many More devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andMore device addresses (64 versus 8) are available to allow many More devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9671 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many More devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and More device addresses (64versus 8) to allow many More devices on the bus without address conflicts.
上传时间： 2013-10-12
上传用户：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many More devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and Moredevice addresses (16 versus 8) are available to allow many More devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many More devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andMore device addresses (16 versus 8) are available to allow many More devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many More devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and Moredevice addresses (64 versus 8) are available to allow many More devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
