The use of the Wind River VxWorks Real-Time Operating System (RTOS) on Virtex™-4embedded PowerPC™ processors continues to be a popular choice for high performanceFPGA designs. The introduction of the Wind River Workbench design environment has enableda new and easier way for designers to control the configuration of the VxWorks kernel. Thisguide shows the steps required to build and configure a ML403 Embedded DevelopmentPlatform to boot and run the VxWorks RTOS. A VxWorks bootloader is created, programmedinto Flash, and used to boot the design. The concepts presented here can be scaled to anyPowerPC enabled development platform.
上传时间： 2013-10-26
上传用户：agent
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上传时间： 2014-01-17
上传用户：Altman
Abstract: This application note explains how to design an intelligent lighting controller that senses and measures the ambient lightlevel with an ambient light sensor (ALS). Equipped with a real-time clock (RTC), the controller also knows when to turn lighting on oroff at specified times. The system presented in this document can be used to control all luminaires that are mains-supply operated.Controller software is also provided in hex format.
上传时间： 2013-11-18
上传用户：AbuGe
为了移植到MPC860，需要修改uC/OS-II中与处理器和编译器相关的部分代码
上传时间： 2013-12-22
上传用户：wangzhen1990
提供了一些ADSP-217x或ADSP-218x DSP芯片的编程事例，运行在uC/OS-II平台下。
上传时间： 2015-03-13
上传用户：qwe1234
利用横向递归算法解决数据组合的问题， 比如数组为a, 长度为len， 横向递归 B display(a,len) b是二维数组，a是一维数组
上传时间： 2015-03-21
上传用户：tb_6877751
杭州利宇泰公司的基于44B0的ARMSys开发板上的大量源代码，包括ADC、ARP、彩色LCD、外部中断、以太网底层函数、FAT16文件系统、Flash ROM、GUI软件包、Helloworld程序、IIC接口、扫描键盘、Ping程序、44B0内置RTC示例、SDRAM接口、定时器示例、触摸屏示例、UART示例和uC/OS-II的移植、应用（包括多任务、任务间通信、中断服务程序）、UDP数据传输、USB固件编写等程序代码和工程。一次性共享给大家使用。可以作为其他samsung44B0开发板上应用程序的下载。
上传时间： 2013-11-30
上传用户：小鹏
能给发家提供这个好东西不容易，希望大家能多多学习，不要辜负了。 uC/GUI是uC/OS-II配套的专用图形界面。这可不是开源软件，也不象uC/OS-II一样可以免费下载，这个是非常昂贵的软件。所以大家拿到后，不要声张，偷着乐吧 ^_^
标签： 家
上传时间： 2015-03-31
上传用户：hewenzhi
CBC下写的串口编程，API函数实例 I wish this site had been around when I was trying to figure out how to make serial communications work in Windows95. I, like many programmers, was hit with the double-whammy of having to learn Windows programming and Win95 serial comm programming at the same time. I found both tasks confusing at best. It was particularly frustrating because I had, over the years, written so much stuff (including lots of serial comm software) for the DOS environment and numerous embedded applications. Interrupt driven serial comm, DMA transfer serial comm, TSR serial comm, C, assembler, various processors... you name it, it had written it. Yet, everything I knew seemed upside-down in the message-driven-callback world of Windows.
上传时间： 2014-06-20
上传用户：cccole0605
