为提升虚拟仪器传输速率与实时性能，扩展监测范围，在VC的软件平台上设计了一种全功能虚拟示波器。与传统虚拟示波器相比，该系统采用嵌入式系统完成信号采集，采用工业以太网为传输介质，通过线性插值算法和多线程编程思想，实现波形显示、参数计算、频谱分析以及波形存储及回放功能。实验结果表明，该虚拟示波器可以实现20 kHz采样频率下的波形精确显示，达到预期的各项指标。 Abstract: o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
上传时间： 2013-11-25
上传用户：wbwyl
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上传时间： 2013-11-07
上传用户：swing
该系统以计算机为依托构建中央信息处理系统CIPS（Central Information Processing System），以Pocket PC作为巡检终端PS（Portable Station），采用SQL Server 2000关系型数据库和SQL Server CE3.0嵌入式数据库技术，集RFID技术、GPS定位技术、信息管理、信息传输等多项技术于一体，完成信息在CIPS和PS之间的交互，实现巡检信息的综合处理。
上传时间： 2013-11-16
上传用户：stvnash
同步技术是跳频通信系统的关键技术之一，尤其是在快速跳频通信系统中，常规跳频通信通过同步字头携带相关码的方法来实现同步，但对于快跳频来说，由于是一跳或者多跳传输一个调制符号，难以携带相关码。对此引入双跳频图案方法，提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息，克服了快速跳频难以携带相关码的困难。分析了同步性能，仿真结果表明该方案同步时间短、虚警概率低、捕获概率高，同步性能可靠。 Abstract: Synchronization is one of the key techniques to frequency-hopping communication system， especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems， synchronization can be achieved by synchronization-head which can be used to carry the synchronization information， but for the fast frequency hopping， Because modulation symbol is transmitted by per hop or multi-hop， it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code， a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code， which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed， and simulation results show that the scheme has the advantages of shorter synchronization time， lower probability of false alarm， higher probability of capture and more reliable of synchronization.
上传时间： 2013-11-23
上传用户：mpquest
提出了一种以ARM微处理器为控制核心的远程无线视频监控终端的设计方案，其监控终端的硬件设计包括视频采集处理、中央管理控制、无线传输3个模块。并给出了监控终端的软件开发平台和开发模式的系统启动代码、嵌入式Linux系统移植以及驱动程序和应用程序。测试结果表明，该监控终端设计方案合理、有效，基本满足监控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上传时间： 2013-11-13
上传用户：wanqunsheng
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
上传时间： 2013-10-28
上传用户：15501536189
The NXP LPC315x combine an 180 MHz ARM926EJ-S CPU core, High-speed USB 2.0OTG, 192 KB SRAM, NAND flash controller, flexible external bus interface, an integratedaudio codec, Li-ion charger, Real-Time Clock (RTC), and a myriad of serial and parallelinterfaces in a single chip targeted at consumer, industrial, medical, and communicationmarkets. To optimize system power consumption, the LPC315x have multiple powerdomains and a very flexible Clock Generation Unit (CGU) that provides dynamic clockgating and scaling.The LPC315x is implemented as multi-chip module with two side-by-side dies, one fordigital fuctions and one for analog functions, which include a Power Supply Unit (PSU),audio codec, RTC, and Li-ion battery charger.
上传时间： 2014-01-17
上传用户：Altman
ORCAD在使用的时候总会出现这样或那样的问题…但下这个问题比较奇怪…在ORCAD中无法输出网表…弹出下面的错误….这种问题很是奇怪…Netlist Format: tango.dllDesign Name: D:\EDA_PROJECT\PROTEL99SE\YK\SV3200\MAIN.DSNERROR [NET0021] Cannot get part.[FMT0024] Ref-des not found. Possible Logical/Physical annotation conflict.[FMT0018] Errors processing intermediate file找了一天没找到问题…终于在花了N多时间后发现问题所在…其实这个问题就是不要使用ORCAD PSPICE 库里面的元件来画电路图…实际中我是用了PSPICE里面和自己制作的二种电阻和电容混合在一起…就会出现这种问题…
上传时间： 2013-11-21
上传用户：zaocan888
Today in many applications such as network switches, routers, multi-computers,and processor-memory interfaces, the ability to integrate hundreds of multi-gigabit I/Os is desired to make better use of the rapidly advancing IC technology.
上传时间： 2013-10-30
上传用户：ysjing
ARM通讯 H-JTAG 是一款简单易用的的调试代理软件，功能和流行的MULTI-ICE 类似。H-JTAG 包括两个工具软件：H-JTAG SERVER 和H-FLASHER。其中，H-JTAG SERVER 实现调试代理的功能，而H-FLASHER则实现了FLASH 烧写的功能。H-JTAG 的基本结构如下图1-1所示。 H-JTAG支持所有基于ARM7 和ARM9的芯片的调试，并且支持大多数主流的ARM调试软件，如ADS、RVDS、IAR 和KEIL。通过灵活的接口配置，H-JTAG 可以支持WIGGLER，SDT-JTAG 和用户自定义的各种JTAG 调试小板。同时，附带的H-FLASHER 烧写软件还支持常用片内片外FLASH 的烧写。使用H-JTAG，用户能够方便的搭建一个简单易用的ARM 调试开发平台。H-JTAG 的功能和特定总结如下： 1. 支持 RDI 1.5.0 以及 1.5.1； 2. 支持所有ARM7 以及 ARM9 芯片； 3. 支持 THUMB 以及ARM 指令； 4. 支持 LITTLE-ENDIAN 以及 BIG-ENDIAN； 5. 支持 SEMIHOSTING； 6. 支持 WIGGLER， SDT-JTAG和用户自定义JTAG调试板； 7. 支持 WINDOWS 9.X/NT/2000/XP； 8．支持常用FLASH 芯片的编程烧写； 9. 支持LPC2000 和AT91SAM 片内FLASH 的自动下载；
上传时间： 2014-12-01
上传用户：Miyuki
