The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上传时间： 2013-10-19
上传用户：bakdesec
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
Providing power for the Pentium® microprocessor family isnot a trivial task by any means. In an effort to simplify thistask we have developed a new switching regulator controlcircuit and a new linear regulator to address the needs ofthese processors. Considerable time has been spent developingan optimized decoupling network. Here are severalcircuits using the new LTC®1266 synchronous buck regulatorcontrol chip and the LT®1584 linear regulator toprovide power for Pentium processors and Pentium VREprocessors. The Pentium processor has a supply requirementof 3.3V ±5%. The Pentium VRE processor requires3.500V ±100mV.
上传时间： 2013-11-01
上传用户：名爵少年
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata acquisition, power monitoring and other applicationsare good candidates for batteryoperation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation mustfunction at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签： Circuitry Operation Single Cell
上传时间： 2013-10-30
上传用户：hz07104032
In predominantly digital systems it is often necessaryto include linear circuit functions. Traditionally, separatepower supplies have been used to run the linear components(see Box, “Linear Power Supplies—Past, Present,and Future”).
标签： Designing Operation Circuits Linear
上传时间： 2013-11-04
上传用户：sdq_123
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
光伏发电是未来新能源发电重要方向之一，而光伏变流器是光伏发电系统的核心。介绍一种基于微网理念的光伏变流器设计。以该变流器为核心的光伏发电系统可以看做一个小型的微网系统。该系统能根据外部电网情况，工作于并网模式和离网模式。介绍了该系统的各个组成部件的设计以及变流器主电路部分器件的选型。最后，由实验样机进行测试。试验结果验证了电路拓扑结构及控制方案的可行性，也说明了系统参数设计方法的正确性。 Abstract: Solar Photovoltaic generation is an important direction of new energy power generation in the future，while photovoltaic converter is the core of photovoltaic generation system. This paper deals with a study on photovoltaic inverter based on the concept of microgrid. This paper describes a system whose core component is the photovoltaic inverter，can work on grid-connected mode or run independently according to the external situation. The paper simply describes the main components of the system. At last，the prototype was produced and tested. Test result has proved feasibility of circuit topology structure and controlling scheme and shown correctness of system parameters.Key words: PV inverter； microgrid； off-grid； storage battery
上传时间： 2014-12-24
上传用户：Shaikh
功能、性能、特点 采用电磁场优化分布的设计原理，使局部放电和局部过热最小。 小型化、高功能的真空灭弧室利用纵向旋转磁场灭弧原理， 有效地保证了截流值小于3A， 使开断性能极为稳定。 弹簧储能机构采用模块化设计，一件多用，使机构主件分布合理，结构简单，性能稳定。 绝缘性能优越可靠，顺利通过了凝露试验，适合在最恶劣的环境条件下运行，并具有比IEC和GB标准要求更高的爬电距离和电气间隙。 接地方式可靠，确保了断路器从工作位置到试验位置接地的连续性。
上传时间： 2013-12-28
上传用户：ommshaggar
When a system designer specifies a nonisolated dc/dc powermodule, considering the needed input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide input voltage range. Narrowinputmodules typically have a nominal input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated input bus—such as those that do not use batterybackup—a narrow-input module is often adequate sincethe input remains fairly stable.Offering greater flexibility, wide-input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-inputdc/dc modules.
标签： Wide-input modules offer dc
上传时间： 2014-12-24
上传用户：dragonhaixm
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
