AEC-Q100 qualified • 12 V and 24 V battery systems compliance • 3.3 V and 5 V logic compatible I/O • 8-channel configurable MOSFET pre-driver – High-side (N-channel and P-channel MOS) – Low-Side (N-channel MOS) – H-bridge (up to 2 H-bridge) – Peak & Hold (2 loads) • Operating battery supply voltage 3.8 V to 36 V • Operating VDD supply voltage 4.5 V to 5.5 V • All device pins, except the ground pins, withstand at least 40 V • Programmable gate charge/discharge currents for improving EMI behavior
标签： configurable Automotive pre-driver suitable channel systems MOSFET fully High side
上传时间： 2019-03-27
上传用户：guaixiaolong
Description The L9352B is an integrated quad Low-Side power switch to drive inductive loads like valves used in ABS systems. Two of the four channels are current regulators with current range from 0 mA to 2.25 A. All channels are protected against fail functions. They are monitored by a status output.
标签： L9352B
上传时间： 2019-03-27
上传用户：guaixiaolong
STM32F驱动L6470 ■ Operating voltage: 8 - 45 V■ 7.0 A out peak current (3.0 A r.m.s.)■ Low RDS(on) Power MOSFETs■ Programmable speed profile and positioning■ Programmable power MOS slew rate■ Up to 1/128 microstepping■ Sensorless stall detection■ SPI interface■ Low quiescent and standby currents■ Programmable non-dissipative overcurrentprotection on high and Low-Side■ Two levels of overtemperature protection
标签： l6470
上传时间： 2022-07-25
上传用户：kingwide
The MAX2691 low-noise amplifier (LNA) is designed forGPS L2 applications. Designed in Maxim’s advancedSiGe process, the device achieves high gain andlow noise figure while maximizing the input-referred 1dBcompression point and the 3rd-order intercept point. TheMAX2691 provides a high gain of 17.5dB and sub 1dBnoise figure.
标签： Amplifier Low-Noise 2691 Band
上传时间： 2014-12-04
上传用户：zaocan888
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
标签： MAXREFDES Lakewood Isolated Output
上传时间： 2013-11-02
上传用户：fengzimili
Abstract: This document details the Riverside (MAXREFDES8#) subsystem reference design, a 3.3V input, 12V (15V) output, isolated power supply. The Riverside reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and one wide input range and adjustable output low-dropout linear regulator (LDO). Test results and hardware files are included.
标签： Riverside MAXREFDES Isolated Output
上传时间： 2013-11-16
上传用户：会稽剑客
Battery powered applications that have a signifi cantamount of time in standby mode, require electrical circuitsto operate with a low quiescent current to preserve batterylife. The LTC3835 synchronous step-down controlleris an excellent solution with its ultralow quiescent current(80μA). Other features make it uniquely qualifi ed tosatisfy the needs of automotive applications. A wide 4Vto 36V input voltage range protects the supply againsthigh input voltage transients and is compatible with lowvoltage cold crank conditions. The constant frequencycurrent-mode architecture with high-side inductor current
上传时间： 2013-11-20
上传用户：stewart·
Traditionally, an Electronic Circuit Breaker (ECB) comprisesa MOSFET, a MOSFET controller and a current senseresistor. The LTC®4213 does away with the sense resistorby using the RDS(ON) of the external MOSFET. The resultis a simple, small solution that offers a signifi cant lowinsertion loss advantage at low operating load voltage.The LTC4213 features two circuit breaking responses tovarying overload conditions with three selectable tripthresholds and a high side drive for an external N-channelMOSFET switch.
上传时间： 2014-03-02
上传用户：lixinxiang
The PCA9519 is a 4-channel level translating I2C-bus/SMBus repeater that enables theprocessor low voltage 2-wire serial bus to interface with standard I2C-bus or SMBus I/O.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling the I2C-bus or SMBusmaximum capacitance of 400 pF on the higher voltage side. The SDA and SCL pins areover-voltage tolerant and are high-impedance when the PCA9519 is unpowered.
标签： 4channel transla level 9519
上传时间： 2013-11-19
上传用户：jisiwole
