This will sample all 8 A/D-channels by the continous mode. Each end of conversion will call an interrupt routine, where the AD-channel is put to Port4[2..0] and the upper nibble of the result is put to Port4[7..4]. Port 4 is connected to the user LEDs of the FlashCan100P Evaluation-Board
标签： will D-channels conversion continous
上传时间： 2013-12-09
上传用户：zm7516678
This example provides a description of how to set a communication with the bxCAN in loopback mode: - transmit and receive a standard data frame by polling at 100Kbit/S - transmit and receive an extended data frame with interrupt at 500Kbit/S - lit some LEDs depending of the program succeed or not
标签： communication description provides loopback
上传时间： 2016-04-24
上传用户：frank1234
This example provides a description of how to use a DMA channel to transfer a word data buffer from memory (Flash) to memory (RAM). The dedicated DMA channel is configured to transfer once a time a 32 word data buffer stored as constant in the Flash memory to another buffer in the RAM memory. The received data are stored in the DST_Buffer. The DMA channel transfer complete interrupt is enabled to generate an interrupt at the end of the buffer transfer. As soon as the transfer is completed an interrupt is generated and in the DMA channel interrupt routine the transfer complete interrupt pending bit is cleared. The data counter is stored before and after the transfer to show that all data has been transfered. TransferStatus gives the data transfer status where it is PASSED if transmitted and received data are the same otherwise it is FAILED
标签： description provides transfer example
上传时间： 2016-04-24
上传用户：ecooo
用STR710控制串口及CC1100进行无线通信，该开发工具为ARM公司的集成开发环境ADS，有完整的工程文件.mcp.
上传时间： 2016-04-25
上传用户：阳光少年2016
基于s32410的GPS开发代码。无操作系统，ADS开发。
上传时间： 2014-10-12
上传用户：xjz632
基于LPC214X 的USB固件升级程序,通过USB接口来升级更新你的应用程序.基于LPC214X USB 固件升级源程序 (USB Firmware Upgrader source code ) 基于含有USB固件升级的LPC214X例程 例程包含下面编译器的工程文件(Rowley CrossWorks Studio(GCC) 1.5, IAR ARM v.4.39, GCC 3.4 (4.10), ARM ADS 1.2, ARM RealView 2.2, Keil RVC v.3 )
上传时间： 2016-04-28
上传用户：txfyddz
在arm下开发程序，使用keil或ads，此模板是周立功光盘里的资料，相当有参考价值
上传时间： 2014-09-04
上传用户：zhaoq123
由三星的2442修改而来,正确引导eboot,请注意用三星公版的硬件配置,具体可以参考QQ2440,因为我在些平台上跑过,具体操作 1.target settings : post-linker:选择为 ARM fromELF 2.ARM assembler与 ARM c Compiler 的 architecture or processor 选择为:ARM920T 3.ARM linker的 output:RO base为 0x00000000 (当仿真时为：0x30000000），layout的 object/sysmbol:为2440init.o section:Init 4.ARM fromELF 的 output:format:plain binary , output file name：nboot.bin 下面为全部源码,注意用ADS编译 2442addr.h 2442addr.inc 2442init.s 2442lib.c 2442lib.h 2442loader-1208.c 2442slib.h 2442slib.s Def.h k9s1208_s.s Memcfg.inc Nand.h Nand_mini.c Option.h Option.inc
标签： post-linker settings target eboot
上传时间： 2016-05-06
上传用户：moshushi0009
s3c2440的dma操作控制程序，在ADS环境编译，运行
上传时间： 2016-05-06
上传用户：libinxny
s3c2440的液晶屏操作控制程序（SHARP/SAMSUNG都可以），在ADS环境编译，运行
上传时间： 2014-11-27
上传用户：wyc199288
