The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
The RT9005A/B is a dual-output Linear regulator for DDR-SDRAM VDDQ supply and termination voltage VTT supply.
上传时间： 2013-11-13
上传用户：lmq0059
The RT9018A/B is a high performance positive voltage regulator designed for use in applications requining very low Input voltage and very low dropout voltage at up to 3A(peak).
上传时间： 2013-10-10
上传用户：geshaowei
生成BCD码。 Name: BIN3toBCD4 Func:2字节二进制整数--->>BCD码四字节转换(Comped BCD) Input: 3进制数人低字节到高字节存放在内部RAM50H，51H,52h单元中 Output: BCD码人低位到高位分别存放在内部RAM53H,54H，55H，56H单元中 USE: R7-R0, 56H-50H
标签： BCD BIN3toBCD4 Comped Input
上传时间： 2015-02-02
上传用户：FreeSky
对c语言的简单语法分析器 文件说明： input.txt内为输入的源程序，包括for，while和if else控制等 output.txt内为输出的二元单词序列 k.txt为关键字表 l.txt为运算符和界符表 i.txt为该输入的源程序的标志符 c.txt为常数表 个别表需要序列号，这时各表的序列号默认为从1开始，每行加1。 使用说明： 在提示符下输入input.txt文件的路径和文件名字， 运行完成后，打开文件output.txt看结果。
上传时间： 2013-12-23
上传用户：pompey
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
标签： multiplication Implement matrices matrix
上传时间： 2014-08-30
上传用户：dsgkjgkjg
2^x mod n = 1 acm竞赛题 Give a number n, find the minimum x that satisfies 2^x mod n = 1. Input One positive integer on each line, the value of n. Output If the minimum x exists, print a line with 2^x mod n = 1. Print 2^? mod n = 1 otherwise. You should replace x and n with specific numbers. Sample Input 2 5 Sample Output 2^? mod 2 = 1 2^4 mod 5 = 1
标签： mod satisfies minimum number
上传时间： 2015-06-02
上传用户：qlpqlq
* * Input * bin_data : binary data * bin_size : binary data length * Mode : operation mode * BASE64_NeedCRLF ---- Need a CRLF every 64 base64-character * BASE64_NotCRLF ---- Need not CRLF between 64 base64-character * * Output * char data * char data length * * Return * 0: success -1: error
标签： binary data operation bin_data
上传时间： 2015-06-04
上传用户：ZJX5201314
Routine mampres: To obtain amplitude response from h(exp(jw)). input parameters: h :n dimensioned complex array. the frequency response is stored in h(0) to h(n-1). n :the dimension of h and amp. fs :sampling frequency (Hz). iamp:If iamp=0: The Amplitude Res. amp(k)=abs(h(k)) If iamp=1: The Amplitude Res. amp(k)=20.*alog10(abs(h(k))). output parameters: amp :n dimensioned real array. the amplitude-frequency response is stored in amp(0) to amp(n-1). Note: this program will generate a data file "filename.dat" . in chapter 2
标签： dimensione parameters amplitude response
上传时间： 2013-12-19
上传用户：xfbs821
Routine mar1psd: To compute the power spectum by AR-model parameters. Input parameters: ip : AR model order (integer) ep : White noise variance of model input (real) ts : Sample interval in seconds (real) a : Complex array of AR parameters a(0) to a(ip) Output parameters: psdr : Real array of power spectral density values psdi : Real work array in chapter 12
标签： parameters AR-model Routine mar1psd
上传时间： 2015-06-09
上传用户：playboys0
