The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
PCA9519 是一个4 通道的I2C 总线/SMBus 中继器，可以实现将低电压两线串行总线接口的处理器与标准的I2C 总线或SMBus I/O 相连。该中继器在电平转换中保持I2C 总线系统所有的模式和特点的同时，允许通过给数据总线（SDA）和时钟总线（SCK）提供双向缓冲区来扩展I2C 总线，从而使I2C 总线或SMBus 在高电压下最大容限电容为400PF。SDA 和SCL 引脚具有耐压保护功能，当PCA9519 掉电时，均呈现出高阻抗特性。
上传时间： 2013-11-23
上传用户：brilliantchen
The PCA9542A is a 1-of-2 bidirectional translating multiplexer, controlled via the I2C-bus.The SCL/SDA upstream pair fans out to two SCx/SDx downstream pairs, or channels.Only one SCx/SDx channel is selected at a time, determined by the contents of theprogrammable control register. Two interrupt inputs, INT0 and INT1, one for each of theSCx/SDx downstream pairs, are provided. One interrupt output, INT, which acts as anAND of the two interrupt inputs, is provided.
上传时间： 2013-12-07
上传用户：europa_lin
PCA9544A 是NXP 公司生产的I2C 总线多路复用器，通过该器件可以将一路I2C 总线扩展为4 路I2C 总线。将1 路上行SDA/SCL 通道扩展为4 路下行通道。通过对内部可编程寄存器进行配置，在同一时间可以任意选择一对SCx/SDx 线。器件拥有四路输入中断，INT0到INT3，分别对应着四路下行通道。该器件还有一个输出中断，输出中断的状态由四个输入中断通过“与”逻辑控制。
上传时间： 2013-11-17
上传用户：woshinimiaoye
PCA9545A/45B/45C 是一款I2C 总线扩展器件，通过它可以将一路I2C 总线扩展为四路，在对内部控制寄存器进行相应配置后，可同时选择一路或者多路下行I2C 总线与上行I2C 总线相连。该器件具有四个中断输入INT0 - INT3 和一个中断输出INT ，分别对应四路下行I2C总线和一路上行I2C 总线，四个中断输入相“与”后控制中断输出INT 状态。
上传时间： 2014-01-25
上传用户：ainimao
The PCA9546A is a quad bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.
上传时间： 2013-11-16
上传用户：cc1915
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
PCA9546A 是一款I2C 多路复用器和开关，能实现I2C 总线扩展、电平转换及总线功能恢复
上传时间： 2013-12-02
上传用户：myworkpost
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
PCA9547 是一款通过I2C 总线控制的八进制双向转换开关。它的每对SCL/ SDA 上行通道可以扩展为八对下行通道。但在某一时刻，由可编程控制寄存器中的内容来决定只有一路SCx/SDx 被选择。由多路复用器的通门，VDD 管脚可以用来限制PCA9547 通过的最高电压，这使得每一对SCL/SDA 可以使用不同的总线电压，因此1.8V、2.5V 或3.3V 的器件都可以在无其它保护的情况下与5V 的器件进行通信。它的外部上拉电阻将总线拉高至每个通道所要求的电压电平，所有I/O 管脚都可以承受5V 的电压。设备上电时由通道0 连接，并且允许主机和下行设备进行直接的通信
上传时间： 2014-12-28
上传用户：sunshine1402
