This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
Explain how to open the Waveform Viewer for Verification ? State how to insert nodes into the Waveform Viewer ? Tell how to assign Stimulus with the Stimulator Selector
标签： Foundation 仿真
上传时间： 2013-11-05
上传用户：gps6888
Abstract: This application note explains how to layout the MAX20021/MAX20022 automotive quad powermanagementICs (PMICs) to maximize performance and minimize emissions. Example images of a fourlayerlayout are provided.
上传时间： 2013-10-10
上传用户：dljwq
Abstract: This reference design explains how to power the Xilinx Zynq Extensible Processing Platform (EPP) and peripheral ICs using
上传时间： 2013-10-13
上传用户：peterli123456
This application note describes how to implement the Bus LVDS (BLVDS) interface in the supported Altera ® device families for high-performance multipoint applications. This application note also shows the performance analysis of a multipoint application with the Cyclone III BLVDS example.
标签： Implementing LVDS 522 Bus
上传时间： 2013-10-26
上传用户：苏苏苏苏
This application note describes how to retrieve user-defined data from Xilinx configurationPROMs (XC18V00 and Platform Flash devices) after the same PROM has configured theFPGA. The method to add user-defined data to the configuration PROM file is also discussed.The reference design described in this application note can be used in any of the followingXilinx FPGA architectures: Spartan™-II, Spartan-IIE, Spartan-3, Virtex™, Virtex-E, Virtex-II,and Virtex-II Pro.
上传时间： 2013-10-09
上传用户：guojin_0704
Express Mode uses an 8-bit wide bus path for fast configuration of Xilinx FPGAs. Thisapplication note provides information on how to perform Express configuration specifically forthe Spartan™-XL family. The Express mode signals and their associated timing are defined.The steps of Express configuration are described in detail, followed by detailed instructions thatshow how to implement the configuration circui
标签： Spartan-XL Express XAPP FPGA
上传时间： 2015-01-02
上传用户：nanxia
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2013-11-01
上传用户：wojiaohs
This Application Note covers the basics of how to use Verilog as applied to ComplexProgrammable Logic Devices. Various combinational logic circuit examples, such asmultiplexers, decoders, encoders, comparators and adders are provided. Synchronous logiccircuit examples, such as counters and state machines are also provided.
上传时间： 2013-11-11
上传用户：y13567890
The standard that governs the design of avioniccomponents and systems, DO-254, is one of the mostpoorly understood but widely applicable standardsin the avionic industry. While information on thegeneral aspects of the standard is easy to obtain, thedetails of exactly how to implement the standard aresketchy. And once an entity develops a process thatachieves compliance, the details of how compliancewas achieved become part of the intellectualproperty of that entity. This white paper focuses onthe details of developing a DO-254 compliantprocess for the design of FPGAs.
上传时间： 2013-11-03
上传用户：ysystc670
