集合式直流电能表（小功率的） 特点： 精确度0.05%满刻度±1位数 可同时量测与显示/直流电压/电流/瓦特（千瓦）/瓦特小时（千瓦小时） 电压输入（DC0-99.99V/0-600.0V）自动变档功能 显示范围0-9999(电流/瓦特/千瓦),0至99999999(八位數瓦特小时)可任意规划 数位RS-485 界面 (Optional) 主要规格： 辅助电源消耗功率：＜0.35VA(DC12V/DC24V) ＜0.5VA（DC48V） ＜1.5VA（AC90-240V(50/60Hz)） 精确度: 0.05% F.S. ±1 digit (23 ±5℃) 输入范围：Auto range(DC0-99.99V/0-600.0V(DC voltage)) 输入抗阻：＞5MΩ（DC voltage） 取样时间：10 cycles/second(total) 过载显示: " doFL " 显示值范围: 0-9999 digit（DCA/W(KW)） 0-9999999.999 digit(WH/(KWH)) RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF"（0-255） RS-485通信协议: Modbus RTU mode 温度系数: 50ppm/℃ (0-50℃) 显示幕:Bight Red LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力:2KVac/1min.(input/output)（RS-485(Isolating)） 1600 Vdc (input/output) （RS-485(Isolating)） 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-20
上传用户：s363994250
Abstract: Many modern industrial, medical, and commercial applications require temperature measurements in the extended temperature rangewith accuracies of ±0.3°C or better, performed with reasonable cost and often with low power consumption. This article explains how platinumresistance temperature detectors (PRTDs) can perform measurements over wide temperature ranges of -200°C to +850°C, with absolute accuracyand repeatability better than ±0.3°C, when used with modern processors capable of resolving nonlinear mathematical equation quickly and costeffectively. This article is the second installment of a series on PRTDs. For the first installment, please read application note 4875, "High-Accuracy Temperature Measurements Call for Platinum Resistance Temperature Detectors (PRTDs) and Precision Delta-Sigma ADCs."
上传时间： 2013-11-06
上传用户：WMC_geophy
The data plane of the reference design consists of a configurable multi-channel XBERT modulethat generates and checks high-speed serial data transmitted and received by the MGTs. Eachchannel in the XBERT module consists of two MGTs (MGTA and MGTB), which physicallyoccupy one MGT tile in the Virtex-4 FPGA. Each MGT has its own pattern checker, but bothMGTs in a channel share the same pattern generator. Each channel can load a differentpattern. The MGT serial rate depends on the reference clock frequency and the internal PMAdivider settings. The reference design can be scaled anywhere from one channel (two MGTs)to twelve channels (twenty-four MGTs).
上传时间： 2013-12-25
上传用户：jkhjkh1982
Delta-sigma ADCs, with their high accuracy and high noiseimmunity, are ideal for directly measuring many typesof sensors. Nevertheless, input sampling currents canoverwhelm high source impedances or low-bandwidth,micropower signal conditioning circuits. The LTC®2484family of delta sigma converters solves this problem bybalancing the input currents, thussimplifying or eliminatingthe need for signal conditioning circuits.
上传时间： 2015-01-03
上传用户：潜水的三贡
The high defi nition multimedia interface (HDMI) is fastbecoming the de facto standard for passing digitalaudio and video data in home entertainment systems.This standard includes an I2C type bus called a displaydata channel (DDC) that is used to pass extended digitalinterface data (EDID) from the sinkdevice (such as adigital TV) to the source device (such as a digital A/Vreceiver). EDID includes vital information on the digitaldata formats that the sink device can accept. The HDMIspecifi cation requires that devices have less than 50pFof input capacitance on their DDC bus lines, which canbe very diffi cult to meet. The LTC®4300A’s capacitancebuffering feature allows devices to pass the HDMI DDCinput capacitance compliance test with ease.
上传时间： 2013-11-21
上传用户：tian126vip
Accurate measurement of the third order intercept pointfor low distortion IC products such as the LT5514 requirescertain precautions to be observed in the test setup andtesting procedure. The LT5514 linearity performance ishigh enough to push the test equipment and test set-up totheir limits. A method for accurate measurement of thirdorder intermodulation products, IM3, with standard testequipment is outlined below.It is also important to correctly interpret the LT5514specification with respect to ROUT, and the impact ofdemo-board transmission-line termination loss whenevaluating the linearity performance, as explained in theLT5514 Datasheet and in Note 1 of this document.
上传时间： 2013-11-14
上传用户：l254587896
基于通用集成运算放大器，利用MASON公式设计了一个多功能二阶通用滤波器，能同时或分别实现低通、高通和带通滤波，也能设计成一个正交振荡器。电路的极点频率和品质因数能够独立、精确地调节。电路使用4个集成运放、2个电容和11个电阻，所有集成运放的反相端虚地。利用计算机仿真电路的通用滤波功能、极点频率和品质因数的独立控制和正交正弦振荡，从而证明该滤波器正确有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
上传时间： 2013-10-09
上传用户：13788529953
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
This application note discusses a variety of approaches for interfacing analog signals to 5V powered systems. Synthesizing a "rail-to-rail" op amp and scaling techniques for A/D converters are covered. A voltage-to-frequency converter, applicable where high resolution is required, is also presented.
上传时间： 2013-10-12
上传用户：181992417
超声波传感器适用于对大幅的平面进行静止测距。普通的超声波传感器测距范围大概是 2cm~450cm，分辨率3mm（淘宝卖家说的，笔者测试环境没那么好，个人实测比较稳定的 距离10cm~2m 左右，超过此距离就经常有偶然不准确的情况发生了，当然不排除笔者技术 问题。） 测试对象是淘宝上面最便宜的SRF-04 超声波传感器，有四个脚：5v 电源脚（Vcc），触发控制端（Trig），接收端（Echo），地端（GND） 附:SRF 系列超声波传感器参数比较 模块工作原理： 采用IO 触发测距，给至少10us 的高电平信号； 模块自动发送8个40KHz 的方波，自动检测是否有信号返回； 有信号返回，通过IO 输出一高电平，高电平持续的时间就是超声波从发射到返回的时间．测试距离=(高电平时间*声速(340m/s))/2; 电路连接方法 Arduino 程序例子： constintTrigPin = 2; constintEchoPin = 3; floatcm; voidsetup() { Serial.begin(9600); pinMode(TrigPin, OUTPUT); pinMode(EchoPin, INPUT); } voidloop() { digitalWrite(TrigPin, LOW); //低高低电平发一个短时间脉冲去TrigPin delayMicroseconds(2); digitalWrite(TrigPin, HIGH); delayMicroseconds(10); digitalWrite(TrigPin, LOW); cm = pulseIn(EchoPin, HIGH) / 58.0; //将回波时间换算成cm cm = (int(cm * 100.0)) / 100.0; //保留两位小数 Serial.print(cm); Serial.print("cm"); Serial.println(); delay(1000); }
上传时间： 2013-11-01
上传用户：xiaoyuer
