摘要：本水位监测报警器使用5V低压直流电源（也可以用3节5号电池代替）就可以对5~15厘米的水位进行监测，用LED显示和数码管显示水位，并可以对不再此范围内的水位发出报警。主要采用CD4066、74LS86、74LS32、CD4511芯片，再加上数码管、蜂鸣器、发光二极管、电阻这些器件组成一个简单而灵敏的监测报警电路，操作简单，接通电源即可工作。因为大部分电路采用数字电路，所以本水位监测报警器还具有耗能低、准确性高的特点。关键字：译码电路 报警电路 监测电路 Abstract: The water level alarm monitoring the use of 5 V low-voltage DC power (can also use three batteries replaced on the 5th) will be able to 5 to 15 centimeters of water level monitoring, with LED display and digital display of water level, and this can no longer Within the scope of a water level alarm. Mainly CD4066, 74LS86, 74LS32, CD4511 chips, coupled with digital control, buzzer, light-emitting diode, the resistance of these devices composed of a simple and sensitive monitoring alarm circuits. Because the majority of circuits using digital circuitry, so the water level monitored alarm system also has low energy consumption, high accuracy of the characteristics. Keyword: Decoding circuit alarm circuit monitoring circuit
上传时间： 2013-11-05
上传用户：王庆才
多功能高集成外围器件6. 1 多功能高集成外围器件82371PCI的英文名称：Peripheral Component Interconnect （外围部件互联PCI总线）；82371是PCI总线组件。ISA是：Industry Standard Architecture（工业标准体系结构）IDE是 （Integrated Device Electronics）集成电路设备简称PIIX4PIIX4器件（芯片）的特点1、是一种支持Pentium和PentiumII微处理器的部件。2、82371对ISA桥来说，是一种多功能PCI总线。3、对可移动性和桌面深绿色环境均提供支持。4、电源管理逻辑。5、被集成化的IDE控制器。6、增强了性能的DMA控制器。 （7）基于两个82C59的中断控制器。（8）基于82C54芯片的定时器。（9）USB（Universal Serial Bus）通用串行总线。（10）SMBus系统管理总线。（11）实时时钟（12）顺应Microsoft Win95所需的功能其芯片的逻辑框图如图6-1所示。 PIIX4芯片逻辑框图6.1.1 概述PIIX4芯片是一个多功能的PCI器件，图6-2 是82371在系统中扮演的角色。（续上图）1. PCI与EIO之间的桥（PIIX4芯片）桥是不对程的，是各类不同标准总线与PCI总线连接，82371AB桥也可理解为一种总线转换译码器和控制器，桥内包含复杂的协议总线信号和缓冲器。(1).在PCI系统内，当PIIX4操作时，它总是作为系统内各种模块的主控设备，如USB和DMA控制器、IDE总线和分布式DMA的主控设备等，而且总是以ISA主控设备的名义出现。(2). 在向ISA总线或IDE总线进行传送操作的传送周期期间作为从属设备使用，并对内部寄存器译码。PIIX4芯片（桥）的配置(1).可以把PIIX4芯片配置成整个ISA总线，或ISA总线的子集，也可扩展成EIO总线。在使用EIO总线时，可以把未使用的信号配置成通用的输入和输出。(2).PIIX4可直接驱动5个ISA插槽；(3).能提供字节-交换逻辑、I/O的恢复支持、等待状态的生成以及SYSCLK的生成。(4).提供X-BUS键盘控制器芯片、BIOS芯片、实时时钟芯片、二级微程序器等的选择。2. IDE接口（总线主控设备的权利和同步DMA方式）IDE接口为4个IDE的设备提供支持，比如IDE接口的硬盘和CD-ROM等。注意：目前硬盘接口有5类：IDE、SCSI、Fibre Channel、IEEE1394和USB等。IDE口几乎在PC机最多，因为便宜。SCSI多用于服务器和集群机。IDE的PIO IDE速率：14MB/s；而总线主控设备IDE的速率：33MB/s在PIIX4芯片的IDE系统内，配有两个各次独立的IDE信号通道。3. 具有兼容性的模块—DMA、定时器/计数器、中断控制器等（1）在PIIX4内的两各82C37 DMA控制器经逻辑的组合，产生7个独立的可编程通道。通道[0：3]是通过与8个二进位的硬件连线实现的。通过以字节为单位的计数进行传送。而通道[5：7]是通过16个二进位的连线实现的，以字为单位的计数进行传送。（2）DMA控制器还能通过PCI总线，处理旧的DMA的两个不同的方法提供支持。（3）计数/定时器模块在功能上与82C54等价。（4）中断控制器与ISA兼容，其功能是两个82C59的功能之和。
上传时间： 2013-11-19
上传用户：3到15
基于单片机控制的二氧化碳浓度测试计:基于CDM4161二氧化碳气体浓度测试模块以及ATtiny26单片机,提出了一种二氧化碳浓度测试计的设计方案。该方案具有硬件电路简单、成本低、可靠性高、测量准确等优点，具有较高的实用价值。 Abstract: Abstract：A desigh scheme of CO2 concentration meter based on CDM4161carbon dioxide concentration test module and ATtiny26micro-controller is presented in this paper.The design scheme features simple hardware circuit,low-cost,high reli-ability，accurate measurement and it has a high practical value.
上传时间： 2013-11-14
上传用户：zjwangyichao
The Infineon TriCore provides an Interrupt System with a high safety standard. Thisdocument contains some instructions on how to initiate an Interrupt from an externaldevice. First it will show you how to trigger an Interrupt Service Request by an impulseon Port 0 or Port 1. Then in the second part of the document you can find hints how todebounce impulses to enable the use of a simple switch as input device.Authors: Thomas Bliem, CQ Nguyen / Infineon SMI MD Apps
上传时间： 2013-11-05
上传用户：uuuuuuu
This application note shows how to write an Inter Integrated Circuit bus driver (I²C) for the Philips P90CL301micro-controller.It is not only an example of writing a driver, but it also includes a set of application interface software routines toquickly implement a complete I²C multi-master system application.For specific applications the user will have to make minimal changes in the driver program. Using the drivermeans linking modules to your application software and including a header-file into the application sourceprograms. A small example program of how to use the driver is listed.The driver supports i.a. polled or interrupt driven message handling, slave message transfers and multi-mastersystem applications. Furthermore, it is made suitable for use in conjunction with real time operating systems, likepSOS+.
上传时间： 2013-11-23
上传用户：weixiao99
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
The P90CL301 is a highly integrated 16/32 bit micro-controller especially suitable for applications requiring lowvoltage and low power consumption. It is fully software compatible with the 68000. Furthermore, it provides bothstandard as well as advanced peripheral functions on-chip.One of these peripheral functions is the I2C bus. This report describes worked-out driver software (written in C) toprogram the P90CL301 I2C interface. It also contains interface software routines offering the user a quick start inwriting a complete I2C system application.
上传时间： 2014-01-06
上传用户：气温达上千万的
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上传时间： 2013-11-02
上传用户：zw380105939
The XA-S3 is a member of Philips Semiconductors’ XA (eXtended Architecture) family of high performance 16-bit single-chip Microcontrollers. The XA-S3 combines many powerful peripherals on one chip. Therefore, it is suited for general multipurpose high performance embedded control functions.One of the on-chip peripherals is the I2C bus interface. This report describes worked-out driver software (written in C) to program / use the I2C interface of the XA-S3. The driver software, together with a demo program and interface software routines offer the user a quick start in writing a complete I2C - XAS3 system application.
上传时间： 2013-11-10
上传用户：liaofamous
