特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 多种输入输出选择（Wide selection of input/output range） 三线式接线自动补偿线路阻抗效应（3 wire configuration automatically compensate line resistance effects） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-17
上传用户：Huge_Brother
特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 宽输入范围200ohm 至 50Kohm（Wide inpuet ranges from 200ohm to 50Kohm） 多种输入输出选择（Wide selection of input/output range） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-28
上传用户：sardinescn
特点（FEATURES） 精确度0.1%满刻度（Accuracy 0.1%F.S.） 多种输入输出选择（Wide selection of input/output range） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2014-12-24
上传用户：qimingxing130
特点（FEATURES） 精确度0.03%满刻度（Accuracy 0.03%F.S.） 频率输入范围0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔离类比输出（16 bit DAC isolating analog output） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-21
上传用户：dljwq
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
Abstract: With its small size and large load (10W) capability, the MAX13256 H-bridge transformer driver is an attractive solution forcharging supercapacitors (supercaps). However, a large capacitance on the output of the circuit can force the driver into fault modeat startup, due to the high initial charge current. This application note presents a solution that allows users to charge a largecapacitance without going into fault.
上传时间： 2013-10-20
上传用户：2728460838
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
