制作基于PIC Mcu 的ADS-B接收机的全套资料，包括SCH、PCB、源码和PC端软件。
上传时间： 2013-04-24
上传用户：cx111111
2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.
上传时间： 2013-10-07
上传用户：ysystc670
PSHLY-B回路电阻测试仪介绍
上传时间： 2013-11-05
上传用户：木子叶1
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
摘要：本文详细叙述了基于FPGA及单片机K实现时码终端系统的设计方法，该系统可用于对国际通用时间格式码IRIG码（简称B码）的解调，以及产生各种采样、同步频率信号，也可作为其它系统的时基和采样、同步信号的基准。关键词：单片机；IRIG-B格式码；FPGA；解调；控制；接口
上传时间： 2013-12-16
上传用户：CSUSheep
100-Gb光传送网（OTN）复用转发器 a. 提供连续数据范围在600 Mbps到14.1 Gbps之间的串行收发器，通过使用方便的部分重新配置功能支持多标准客户侧接口； b. 44个独立发送时钟域，提高了时钟灵活性； c. 收发器集成电信号散射补偿（EDC）功能，可直接驱动光模块（SFP+、SFP、QSFP、CFP）； d. 支持下一代光接口的28-Gbps收发器； e. 替代外部压控晶体振荡器（VCXO）的高级fPLL。
上传时间： 2013-11-19
上传用户：zhyiroy
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2014-08-16
上传用户：adada
针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言编写出源程序，在Virtex-II Pro 开发板上成功实现了整个系统。测试结果表明该系统正确实现了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上传时间： 2013-11-06
上传用户：liu123
TKS仿真器B系列快速入门
上传时间： 2013-10-31
上传用户：aix008
为了满足超声波探伤检测的实时性需求，通过研究超声波探伤的工作原理，提出了基于FPGA芯片的实时信号处理系统实现方案及硬件结构设计，并根据FPGA逻辑结构模型实现了软件系统的模块化设计。根据实验测试及统计数据得出，基于FPGA芯片的信号处理系统提高了探伤检测的准确性与稳定性，满足了探伤过程中B超显示的实时性要求。
上传时间： 2013-10-23
上传用户：731140412
