With the continued growth in the world's population, there is a need to Ensure availability of enough food to feed everyone. Advances in science and technology have helped not only to increase food production, but also to reduce food wastage. However, the latter has the potential to be improved to a significant extent through appropriate matching of supply and demand, and with proper handling during storage and transit. Given the amount of food wastage that occurs after a food item leaves the “farm” on its way to the “fork,” and the availability of means to reduce such wastage, there really is no excuse for feigned ignorance.
标签： Automation Industry Network Sensor RFID Food and the in
上传时间： 2020-06-08
上传用户：shancjb
The countless technological advances of the twentieth century require that futureengineering educationemphasizebridging thegapbetweentheoryand the real world.Thisedition hasbeenprepared withparticular attentiontothe needs of undergraduates, especially those who seek a solid foundation in control theory aswellas an ability tobridgethe gapbetween control theory and itsreal- world applications.To help the reader achieve this goal, computer-aided design accuracy checks (CADAC) are used throughout the text to encourage good habits of computerliteracy.Each CADAC uses fundamentalconcepts to Ensure the viability of a computer solution.
标签： Analysis Control Linear Design System Fifth and
上传时间： 2020-06-10
上传用户：shancjb
电子书-RTL Design Style Guide for Verilog HDL540页A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and Ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
标签： RTL verilog hdl
上传时间： 2022-03-21
上传用户：canderile
基于FPGA设计的相关论文资料大全 84篇用FPGA实现FFT的研究 刘朝晖 韩月秋 摘 要 目的 针对高速数字信号处理的要求，给出了用现场可编程门阵列(FPGA)实现的 快速傅里叶变换(FFT)方案.方法 算法为按时间抽取的基4算法，采用递归结构的块浮点运 算方案，蝶算过程只扩展两个符号位以适应雷达信号处理的特点，乘法器由阵列乘法器实 现.结果 采用流水方式保证系统的速度，使取数据、计算旋转因子、复乘、DFT等操作协 调一致，在计算、通信和存储间取得平衡，避免了瓶颈的出现.结论 实验表明，用FPGA 实现高速数字信号处理的算法是一个可行的方案. 关键词 离散傅里叶变换； 快速傅里叶变换； 块浮点运算； 可编程门阵列 分类号 TP39； TN957.511 Implementation of FFT with FPGA Technology Liu Zhaohui Han Yueqiu (Department of Electronics Engineering, Beijing Institute of Technology, Beijing 100081) Abstract Aim To propose a scheme for implementing FFT with FPGA in accor-dance with the requirement for high speed digital signal processing. Methods The structure of FPGA and requirement of system were considered in the experiment, radix-4 algorithm of DIT and recursive structure were adopted. The group float point arithmetic operation was used in the butterfly and the array multiplier was used to realize multiplication. Results The pipeline pattern was used to Ensure the system speed, it made fetching data, calculating twiddle factor, complex multiplication and D
标签： fpga
上传时间： 2022-03-23
上传用户：
对某四轮独立驱动电动汽车轮毂电机进行研究,设计一种永磁无刷直流电机控制器.以STM32F103RBT6芯片为基础,对电机驱动电路、采样电路和保护电路分别进行硬件设计与分析;同时,采用模块化软件设计方案,对该控制器的软件系统进行升级.实验验证表明:所设计的电机控制器能使电机响应迅速、转速稳定、无超调,且电动车动力输出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental results show that the designed motor controller can Ensure the motor fast response,stable speed,no overshoot,and good power output performances.
上传时间： 2022-03-26
上传用户：qingfengchizhu
