为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2014-01-13
上传用户：qoovoop
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2014-07-24
上传用户：caiguoqing
多径干扰信号是导航接收机测量过程中遇到的主要误差源之一。针对Galileo系统以及GPS现代化过程中拟使用的BOC调制信号，研究了基于Strobe相关的BOC信号跟踪过程中的多径抑制方法。分析了多径效应对码跟踪精度的影响，从鉴相函数入手，提出了一种新的En-Strobe相关法。运用窄相关法、Strobe相关法和En-Strobe相关法对BOC（1，1）信号和CBOC（6，1，1/11）信号进行多径抑制性能分析。仿真结果表明En-Strobe相关法在中短延迟的情况下能够很好的抑制多径误差，且性能优于窄相关法和Strobe相关法。
上传时间： 2013-10-25
上传用户：脚趾头
针对飞行模拟器座舱数据采集的复杂性，设计了一种基于以太网分布式的数据采集控制系统，该系统是RCM5700微处理器模块上的以太网应用。在系统的基础上具体讨论了PoE技术的应用，在传输数据的网线上同时提供电流，提出并实现了一种包括辅助电源在内的完整可靠的PoE供电方案。设计采用美国国家半导体的LM5073和LM5576并根据不同的负载情况，进行稳定可靠的电压转换，以满足数据采集电路的要求。实验结果表明：该设计稳定可靠，满足低于13 W的采集节点供电要求，提高了模拟器信号采集系统的通用性和标准化程度，避免了以往数据采集节点单独繁琐的电源设计。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was designed. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上传时间： 2013-11-09
上传用户：xyipie
为提升虚拟仪器传输速率与实时性能，扩展监测范围，在VC的软件平台上设计了一种全功能虚拟示波器。与传统虚拟示波器相比，该系统采用嵌入式系统完成信号采集，采用工业以太网为传输介质，通过线性插值算法和多线程编程思想，实现波形显示、参数计算、频谱分析以及波形存储及回放功能。实验结果表明，该虚拟示波器可以实现20 kHz采样频率下的波形精确显示，达到预期的各项指标。 Abstract: o enhance the transfer rate and real-time of virtual instrument performance， expand scope of monitoring， this paper uses the VCs software platform to design a fully functional virtual oscilloscope. Compared with traditional virtual oscilloscope， this system adopts the embedded system to complete the data acquisition， industrial Ethernet as the transmission medium used by the linear interpolation algorithm and multi-threaded programming ideas， namely to achieve waveform display， parameter calculation， spectrum analysis and waveform storage and playback. Experimental results show that the virtual oscilloscope can accurately display the waveform with 20kHz sampling frequency， and achieve the desired targets.
上传时间： 2013-11-25
上传用户：wbwyl
在现代通信系统中，电话语音的频带被限制在300 Hz～4 kHz的范围内，带来了语音可懂度和自然度的降低。为了在不增加额外成本的前提下提高语音的可懂度和自然度，进行了电话语音频带扩展的研究。提出了一种改进的基于码本映射的语音带宽扩展算法：在码本映射的过程中，使用加权系数来得到映射码本。客观测试结果表明，用此算法得到的宽带语音的谱失真度比用一般的码本映射降低至少2%。主观测试结果表明，用此算法得到的宽带语音具有更好的可懂度和自然度。 Abstract: In modern communication systems， the bandwidth of telephone speech is limited from 300Hz to 4 kHz， which reduces the intelligibility and naturalness of speech. Telephone speech bandwidth extension is researched to get wideband speech and to improve its intelligibility and naturalness， without increasing extra costs. This paper put forward an improved algorithm of speech bandwidth extension based on codebook mapping. In the process of codebook mapping， weighted coefficients were used to get mapping codebook. Objective tests show that spectral distortion of wideband speech obtained by this algorithm reduces at least 2%， comparing to conditional codebook mapping. Subjective tests show that the wideband speech obtained by this algorithm has better intelligibility and naturalness.
上传时间： 2014-12-29
上传用户：15501536189
RENYWELL有着数多年安全控制产品研发、生产的经验。来自RENYWELL的安全可以给工厂和设备提供最优的安全可靠监控。应用符合系列安全标准的最高安全登记。EN ISO 13849-1 标准PL“e”级、EN IEC 62061标准SILCL 3级、EN IEC 61508标准SIL 3级。
上传时间： 2013-10-12
上传用户：Bert520
特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: 0-9999（PV,SV） 0-999999(TV) 显示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-24
上传用户：wvbxj
特点 显示值范围-199999至999999位數 最高輸入頻率 5KHz 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 定位基准值可任意設定 比較磁滯值可任意設定 数位化指拨设定操作简易 3组继电器输出功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <5KHz 定位置范围: -199999 to 999999 second adjustabl 比较磁滞范围: 0 to 9999 adjustable 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 显示幕: Red high efficiency LEDs high 9.2mm (.36") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2014-12-03
上传用户：xjz632
特点 精确度0.25%滿刻度 ±1位數 输入配线系统可任意选择 CT比可任意设定 具有异常电流值与异常次数记录保留功能 电流过高或过低检测可任意设定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 辅助电源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精确度: 0.25% F.S. ±1 digit 输入负载: <0.2VA (Current) 最大过载能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 输入电流范围: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器磁滞范围: 0-999 digit adjustable 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-14
上传用户：wanghui2438
