Abstract: Class D amplifiers are typically very efficient, making them ideal candidates for portable applications that require longbattery life and low thermal Dissipation. However, electromagnetic interference (EMI) is an issue that commonly accompanies theClass D switching topology. Active-emissions limiting reduces radiated emissions and enables "filterless" operation, allowingdesigners to create small, efficient portable applications with low EMI.
上传时间： 2013-11-23
上传用户：哈哈hah
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power Dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上传时间： 2013-10-22
上传用户：rocketrevenge
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power Dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power Dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat Dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
The LTM4601 DC/DC μModule regulator is a completehigh power density stepdown regulator for up to 12Acontinuous (14A peak) loads. The device is housed ina small 15mm ¥ 15mm ¥ 2.8mm LGA surface mountpackage, thus the large power Dissipation is a challengein some applications. This thermal application note willprovide guidelines for using the μModule regulator inambient environments with or without air fl ow. Loadcurrent derating curves are provided for several inputvoltages and output voltages versus ambient temperatureand air fl ow.
上传时间： 2013-10-19
上传用户：bakdesec
Introduction ? ? The ARM Cortex -A8 microprocessor is the first applications microprocessor in ARM!ˉs new Cortex family. With high performance and power efficiency, it targets a wide variety of mobile and consumer applications including mobile phones, set-top boxes, gaming consoles and automotive navigation/entertainment systems. The Cortex-A8 processor spans a range of performance points depending on the implementation, delivering over to 2000 Dhrystone MIPS (DMIPS) of performance for demanding consumer applications and consuming less than 300mW for low-power mobile devices. This translates into a large increase in processing capability while staying with the power levels of previous generations of mobile devices. Consumer applications will benefit from the reduced heat Dissipation and resulting lower packaging and integration costs.
标签： microprocessor Introduction applications Cortex
上传时间： 2013-12-09
上传用户：xzt
The PW4554 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger.The charger uses a CC/CV charge profile required by Li-ion battery. The charger accepts an inputvoltage up to 24V but is disabled when the input voltage exceeds the OVP threshold, typically 6.8V,to prevent excessive power Dissipation. The 24V rating eliminates the over-voltage protection circuitrequired in a low input voltage charger
标签： pw4554
上传时间： 2022-02-11
上传用户：
以AT89S52单片机为控制核心,采用电容降压技术,Buck电路拓扑,PWM驱动模块和功率器件散热设计,通过高速的数据采集、主功率输入输出模块和控制模块,设计一种新型智能车载充电器.在充电过程中,通过负脉冲瞬间放电实现对铅酸蓄电池的再生修复,提高电池的有效容量,延长使用寿命.该充电器体积小、速度快、效率高、可靠性好.With AT89S52 single chip computer as the control core,a new type of intelligent car-carried charger was designed by using capacitance step-down technology,Buck circuit topology,PWM driving module and power device heat Dissipation design,through high-speed data acquisition,main power input and output module and control module.In the charging process,the regeneration and repair of lead-acid batteries are realized by instantaneous discharge of negative pulse,which improves the effective capacity of batteries and prolongs their service life.The charger has the advantages of small size,fast speed,high efficiency and good reliability.
标签： 车载充电器
上传时间： 2022-03-27
上传用户：
