输入电压 5V/9V/12V/15V/24V DC 输出电压 3.3V/5V/9V/12V/15V/24V DC 如需其它规格,请咨询顺源科技公司 电气特性 以下数据除特殊说明外,均是在TA=25° C, 标称输入电压, 额定输出电流时测得. 输入特性 电压范围 +/- 10 % 滤波 陶瓷电容 隔离特性 额定电压 1000 VDC 泄漏电流 1 m A 电阻 109 Ohm 电容 60 p TYP. 输出特性 电压精度 +/- 5 %, max. ( 20 MHz BW) 纹波及噪音 150mV p-p, max. 可持续短路时间 即时(
标签： BxxxxLS-xW
上传时间： 2014-09-09
上传用户：拔丝土豆
移动电源方案功能要求: 1、单芯片控制充电、升压输出、电量指示功能，输出电流可达1A，效率90%以上 按开关键开机6灯频闪几次后待机， LI为充电指示，L2频闪指示有输出。L2I常亮为输出充满指示，L3-L6为电量指示。在输出时L2频闪。充电时LI频闪。当有负载设备连接时自动输出，无负载电流转为待机。 当按开关工作后，无负载（无操作）10秒自动关机。 2、移动电源方案，单芯片控制为内电池充电、升压输出、电量显示、边充边放；输入电压5V、300-1000MA，输出电压5V、；输出电流可达1A，输出效率90%以上 1）、电性能参数： USB输入电压：DC 5V 输出DC5V
上传时间： 2013-11-19
上传用户：wangfei22
该文提出一种新颗的三电平LLc串联电流谐振型Dc，Dc变换器。每个主开关电压应力是输入电压的一半，并且全范围实现zvs而不用附加任何电路。整流二极管工作在zcs状态。该变换器通过_次谐振的手段使得以较小的频率变化范围就可以实现较大的输入输出调节范围。整个变换器只需一颗磁元件。
上传时间： 2013-10-16
上传用户：604759954
内涵PCB及其原理图（原PCB为crazyboye所制，Gavin尽量把双面改一面，因为学校没有制版机）
上传时间： 2013-11-24
上传用户：674635689
随着功率开关器件的发展，电力电子装置日益小型化和高频化，电气性能大幅提高，但是随之产生的高次谐波却对电网造成严重污染。在电力电子设备中，整流器(AC／DC变流器)占有较大的比例，是主要的污染源。由于固态感应加热电源对于电网呈现非线性特性，从电网中输出的电流就不是标准的正弦曲线。高频谐波电流对电力设施产生过热或其他危害。 Boost电路应用到功率因数校正方面已经较为成熟，对于几百瓦小功率的功率因数校正，常规的电路是可以实现的。但是对于大功率诸如感应加热电源，还存在很多的实际问题。为了解决开关器件由于二极管反向恢复时产生的冲击电流而易损坏的情况，减少开关器件在高频下的开关损耗，本文采用一种无源无损缓冲电路取代传统的LC滤波电路。在分析了软开关电路的工作原理以及逆变模块的分时-移相功率控制策略后，应用Matlab软件进行了仿真，并通过实验结果验证了理论分析的正确性。
上传时间： 2014-12-24
上传用户：RQB123
资料都是我搜集的，不是原创。供学习用
上传时间： 2013-12-30
上传用户：ryb
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
In a recent discussion with a system designer, the requirementfor his power supply was to regulate 1.5Vand deliver up to 40A of current to a load that consistedof four FPGAs. This is up to 60W of power that must bedelivered in a small area with the lowest height profi lepossible to allow a steady fl ow of air for cooling. Thepower supply had to be surface mountable and operateat high enough effi ciency to minimize heat dissipation.He also demanded the simplest possible solution so histime could be dedicated to the more complex tasks. Asidefrom precise electrical performance, this solution had toremovethe heat generated during DC to DC conversionquickly so that the circuit and the ICs in the vicinity do notoverheat. Such a solution requires an innovative designto meet these criteria:
上传时间： 2013-11-24
上传用户：defghi010
