摘 要：直流稳压电源一般由电源变压器，整流电路，滤波电路及稳压电路所组成。变压器把市电交流电压变为所需要的低压交流电，整流器把交流电变为直流电，经滤波后，稳压器再把不稳定的直流电压变为稳定的直流电压输出。本设计主要采用直流稳压构成集成稳压电路，通过变压，整流，滤波，稳压过程将220V交流电，变为稳定的直流电，并稳定输出直流电压。 1.系统设计思路： 线性稳压电源的主要结构如下图所示： 图1 线性稳压电源主要结构
上传时间： 2013-10-15
上传用户：jiangfire
MAX1963A/MAX1976A低压差线性稳压器的工作电压为+1.62V至+3.6V，可保证提供300mA连续负载电流和100mV低压差。高精度(±0.5%)输出电压在内部进行微调，预置范围为+0.75V至+3.0V。当输出电压达到稳压值后，低电平有效、开漏极复位输出至少保持2.2ms (MAX1963A)或70ms (MAX1976A)复位状态。该系列器件提供薄型SOT23和薄型DFN两种封装。内部pMOS调整管具有较低的电源电流，且不受负载电流和压差的影响，因此该系列器件非常适用于便携式电池供电的设备。
上传时间： 2013-11-02
上传用户：爱死爱死
电子发烧友网：本文是小编从电子发烧友网论坛上淘过来的，觉得内容还可以，所以在这里跟大家一起分享分享。电源设计专家亲授电源设计秘诀，助您的设计一臂之力! 一 反激式电源中的铁氧体磁放大器 对于两个输出端都提供实际功率(5 V 2 A 和 12 V 3 A，两者都可实现± 5%调节)的双路输出反激式电源来说，当电压达到 12 V 时会进入零负载状态，而无法在 5%限度内进行调节。线性稳压器是一个可实行的解决方案，但由于价格昂贵且会降低效率，仍不是理想的解决方案。我们建议的解决方案是在 12 V 输出端使用一个磁放大器，即便是反激式拓扑结构也可使用。 为了降低成本，建议使用铁氧体磁放大器。然而，铁氧体磁放大器的控制电路与传统的矩形磁滞回线材料(高磁导率材料)的控制电路有所不用。铁氧体的控制电路(D1 和 Q1)可吸收电流以便维持输出端供电。该电路已经过全面测试。变压器绕组设计为 5 V 和 13 V 输出。该电路在实现 12 V 输出± 5%调节的同时，甚至还可以达到低于 1 W 的输入功率(5 V 300 mW和12V零负载)
上传时间： 2013-10-30
上传用户：lwq11
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
实用资料
上传时间： 2013-11-18
上传用户：lindor
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
The power appetite of large TFT-LCDs appears to beinsatiable. Power supplies must feed increasing numbersof transistors and improved display resolutions, and doso without taking much space.
上传时间： 2014-12-24
上传用户：小小小熊
Automotive batteries, industrial power supplies, distributedsupplies and wall transformers are all sources ofwide-ranging high voltage inputs. The easiest way to stepdown these sources is with a high voltage monolithicstep-down regulator that can directly accept a wide inputrange and produce a well-regulated output. The LT®3493accepts inputs from 3.6V to 36V and LT3481 acceptsinputs from 3.6V to 34V. Both provide excellent lineand load regulation and dynamic response. The LT3481offers a high effi ciency solution over a wide load range andkeeps the output ripple low during Burst Mode® operationwhile the LT3493 provides a tiny solution with minimalexternal components. The LT3493 operates at 750kHzand the LT3481 has adjustable frequency from 300kHzto 2.8MHz. High frequency operation enables the use ofsmall, low cost inductors and ceramic capacitors.
上传时间： 2014-12-24
上传用户：Pzj
The LTC®3569 is a compact power solution for handhelddevices. Its tiny 3mm × 3mm QFN package includesthree buck regulators with individually programmableoutput voltages. One regulator supports load currentsup to 1200mA, while the other two support currents to600mA. Two regulators can be paralleled for increasedload capability. Each current-mode regulator is internallycompensated with excellent load and line regulation. Acomplete 2- or 3-output solution requires a minimumof external passive components.
上传时间： 2013-10-11
上传用户：yxgi5
The LTC3546 is a dual output current mode buck regulatorwith fl exible output current partitioning. Beyondthe advantages normally associated with dual outputregulators (reduced size, cost, EMI and part count, withimproved effi ciency), the LTC3546’s outputs can bepartitioned for either 3A and 1A outputs, or two 2A outputs.This increases its application range and simplifi esmultiple supply rail designs. A confi gurable Burst Mode®clamp for each output sets the current transition levelbetween Burst Mode operation and forced continuousconduction mode to optimize effi ciency over the entireoutput range. An adjustable switching frequency up to4MHz and internal power MOSFET switches allow forsmall and compact footprints.
上传时间： 2013-11-04
上传用户：yxgi5
