移动电源方案功能要求: 1、单芯片控制充电、升压输出、电量指示功能，输出电流可达1A，效率90%以上 按开关键开机6灯频闪几次后待机， LI为充电指示，L2频闪指示有输出。L2I常亮为输出充满指示，L3-L6为电量指示。在输出时L2频闪。充电时LI频闪。当有负载设备连接时自动输出，无负载电流转为待机。 当按开关工作后，无负载（无操作）10秒自动关机。 2、移动电源方案，单芯片控制为内电池充电、升压输出、电量显示、边充边放；输入电压5V、300-1000MA，输出电压5V、；输出电流可达1A，输出效率90%以上 1）、电性能参数： USB输入电压：DC 5V 输出DC5V
上传时间： 2013-11-19
上传用户：wangfei22
EG8010是一款数字化的、功能很完善的自带死区控制的纯正弦波逆变发生器芯片，应用于DC-DC-AC两级功率变换架构或DC-AC单级工频变压器升压变换架构，外接12MHz晶体振荡器，能实现高精度、失真和谐波都很小的纯正弦波50Hz或60Hz逆变器专用芯片。该芯片采用CMOS工艺，内部集成SPWM正弦发生器、死区时间控制电路、幅度因子乘法器、软启动电路、保护电路、RS232串行通讯接口和12832串行液晶驱动模块等功能。 应用领域 单相纯正弦波逆变器 光伏发电逆变器 风力发电逆变器 不间断电源UPS系统 数码发电机系统 中频电源 单相电机调速控制器 单相变频器 正弦波调光器 正弦波调压器 正弦波发生器 逆变焊机
上传时间： 2014-07-04
上传用户：fairy0212
双DC-DC变换器
上传时间： 2013-10-23
上传用户：woshiayin
A number of conventional solutions have been available forthe design of a DC/DC converter where the output voltageis within the input voltage range—a common scenarioin Li-Ion battery-powered applications—but none werevery attractive until now. Conventional topologies, suchas SEPIC or boost followed by buck, have numerousdisadvantages, including low effi ciency, complex magnetics,polarity inversion and/or circuit complexity/cost. TheLTC®3785 buck-boost controller yields a simple, effi cient,low parts-count, single-converter solution that is easyto implement, thus avoiding the drawbacks associatedwith traditional solutions.
上传时间： 2013-10-21
上传用户：ljt101007
Speed and accuracy don’t always go hand-in-handin DC/DC converter systems—that is, until now. TheLTC3811 is a dual output, fi xed frequency current modeDC/DC switching regulator controller designed for one oftoday’s most demanding power supply applications: highcurrent, low voltage processor core supplies.
上传时间： 2013-11-21
上传用户：aix008
DC-link Automotive: MKP1849 (Customized)电动汽车电驱直流母线电容（顾客订制品）MKP1849系列.MKP1849-可集成母线排，大大降低了寄生电感，提高了系统稳定性。
上传时间： 2013-10-13
上传用户：nanfeicui
AN22 details the theoretical and application aspects of the LT1088 thermal RMS/DC converter. The basic theory behind thermal RMS/DC conversion is discussed and design details of the LT1088 are presented. Circuitry for RMS/DC converters, wideband input buffers and heater protection is shown.
上传时间： 2013-10-16
上传用户：china97wan
当前，太阳能光伏市场(包括光伏模块和逆变器)正以每年约30%的年累积速 度增长。太阳能逆变器的作用是将随太阳能辐射及光照变化的DC 电压转换成为 电网兼容的AC 输出；而对于广大电子工程师而言，太阳能逆变器是一个值得高 度关注的技术领域。因此下文将介绍太阳能逆变器设计所需注意的技术要点、挑 战以及相应的解决方法。 基本设计标准 基于太阳能逆变器的专用性以及保持设计的高效率，它需要持续监视太阳能 电池板阵列的电压和电流，从而了解太阳能电池板阵列的瞬时输出功率。它还需 要一个电流控制的反馈环，用于确保太阳能电池板阵列工作在最大输出功率点， 以应付多变的高输入。目前，太阳能逆变器已有多种拓扑结构，最常见的是用于 单相的半桥、全桥和Heric(Sunways 专利)逆变器，以及用于三相的六脉冲桥和 中点钳位（NPC）逆变器；图1 所示是这些逆变器的拓扑图(Microsemi 图源)。 同时，设计还需遵从安全规范，并在电网发生故障的时候可以快速断开与电网的 连接。因此，太阳能逆变器的基本设计标准包括额定电压、容量、效率、电池能 效、输出AC 电源质量、最大功率点跟踪（MPPT）效能、通信特性和安全性
标签： 太阳能逆变器
上传时间： 2014-12-24
上传用户：三人用菜
When a system designer specifies a nonisolated dc/dc powermodule, considering the needed input voltage range isequally as important as considering the required performanceattributes and features. Generally, nonisolated moduleshave either a narrow or a wide input voltage range. Narrowinputmodules typically have a nominal input voltage of3.3, 5, or 12 V. For systems that operate from a tightlyregulated input bus—such as those that do not use batterybackup—a narrow-input module is often adequate sincethe input remains fairly stable.Offering greater flexibility, wide-input modules operatewithin a range of 7 to 36 V, which includes the popular12- or 24-V industrial bus. This enables a single module tobe used for generating multiple voltages. These modulesare ideal for industrial controls, HVAC systems, vehicles,medical instrumentation, and other applications that usea loosely regulated distribution bus. In addition, systemspowered by a rectifier/battery charger with lead-acidbattery backup almost always require wide-input modules.System designers who choose power supplies may wantto take a close look at the latest generation of wide-inputdc/dc modules.
标签： Wide-input modules offer dc
上传时间： 2014-12-24
上传用户：dragonhaixm
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
