内涵PCB及其原理图（原PCB为crazyboye所制，Gavin尽量把双面改一面，因为学校没有制版机）
上传时间： 2013-11-24
上传用户：674635689
随着功率开关器件的发展，电力电子装置日益小型化和高频化，电气性能大幅提高，但是随之产生的高次谐波却对电网造成严重污染。在电力电子设备中，整流器(AC／DC变流器)占有较大的比例，是主要的污染源。由于固态感应加热电源对于电网呈现非线性特性，从电网中输出的电流就不是标准的正弦曲线。高频谐波电流对电力设施产生过热或其他危害。 Boost电路应用到功率因数校正方面已经较为成熟，对于几百瓦小功率的功率因数校正，常规的电路是可以实现的。但是对于大功率诸如感应加热电源，还存在很多的实际问题。为了解决开关器件由于二极管反向恢复时产生的冲击电流而易损坏的情况，减少开关器件在高频下的开关损耗，本文采用一种无源无损缓冲电路取代传统的LC滤波电路。在分析了软开关电路的工作原理以及逆变模块的分时-移相功率控制策略后，应用Matlab软件进行了仿真，并通过实验结果验证了理论分析的正确性。
上传时间： 2014-12-24
上传用户：RQB123
资料都是我搜集的，不是原创。供学习用
上传时间： 2013-12-30
上传用户：ryb
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
在航天等空间产品中使用的分布式供电系统中，总体电路一般只提供27~30 V的直流一次电源，各单机产品大多采用DC/DC模块将该一次电源转换为所需的二次电源，并实现一次地与二次地的隔离。分析了INTERPOINT公司的DC/DC模块的输入端反接后，输入电压对DC/DC模块、电源保护滤波电路及负载的影响，通过仿真与验证试验，得出电源模块输入端反接后单机产品中电源保护电路发生作用，对产品中负载无影响，可以继续使用。电源模块失效分析对航天产品中电源模块中出现类似的故障后的处理提供了参考。
上传时间： 2013-11-05
上传用户：kangqiaoyibie
一般指连接交流电源的线圈称之为「一次线圈」(Primamary coil)；而跨于此线圈的电压称之为「一次电压」。在二次线圈的感应电压可能大于或小于一次电压，是由一次线圈与二次线圈问的「匝数比」所决定的。因此，变压器区分为升压与降压变压器两种。
标签： 变压器
上传时间： 2013-12-28
上传用户：gxmm
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
本应用报告描述了一个具有宽电压输入的智能电池充电器。其中的参考设计实现了在MSP430微控制器和兼容SMBus的电池电量计之间进行通信的系统管理总线（SMBus）协议。MSP430 器件通过SMBus 从电量计获取电压、电流和其它一些参数，之后通过调节输出到dc/dc变换器模块的PWM 占空比来传递电池所需的电量。
上传时间： 2013-10-28
上传用户：1427796291
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
