In this paper, two types of MMIC voltage Controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上传时间： 2013-10-17
上传用户：xjz632
The LTC®4155 and LTC4156 are dual multiplexed-inputbattery chargers with PowerPath™ control, featuring I2Cprogrammability and USB On-The-Go for systems suchas tablet PCs and other high power density applications.The LTC4155’s float voltage (VFLOAT) range is optimizedfor Li-Ion batteries, while the LTC4156 is optimized forlithium iron phosphate (LiFePO4)batteries, supportingsystem loads to 4A with up to 3.5A of battery chargecurrent. I2C controls a broad range of functions and USBOn-The-Go functionality is Controlled directly from theUSB connector ID pin.
上传时间： 2013-10-09
上传用户：hanhanj
提出了一种24V/15A 直流变换器的设计方法。主电路采用推挽正激电路，通过在传统推挽电路的基础上增加一个箝位电容，起到抑制偏磁和开关管关断电压尖峰的作用。控制采用峰值电流控制方式（Peak CurrentControlled Model，简称PCCM），为了克服其对占空比要求的限制，加入了斜坡补偿环节。在进行详细的理论分析基础上，给出了主电路和控制电路一些关键参数的设计步骤；最后通过原理样机的研制，验证了理论分析的正确性。
上传时间： 2013-10-23
上传用户：dick_sh
Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads Controlled in time.
上传时间： 2013-10-18
上传用户：如果你也听说
Analog Inputs and Outputs in an S7 PLC are represented in the PLC as a 16-bit integer. Over the nominal span of the analog input or output, the value of this integer will range between - 27648 and +27648. However, it is easier to use the analog values if they are scaled to the same units and ranges as the process being Controlled. This applications tip describes methods for scaling analog values to and from engineering units.
上传时间： 2013-11-17
上传用户：3294322651
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply Controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote Controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of Controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-Controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
设计一种基于ATmega16L单片机的温度控制系统，阐述该系统的软硬件设计方案。采用模块化设计方法，利用增量式PID算法使被控对象的温度值趋于给定值。实验结果表明该系统具有良好的检测和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of Controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
上传时间： 2013-10-09
上传用户：stvnash
