The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9546A is a quad bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to four downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.
上传时间： 2013-11-16
上传用户：cc1915
The PCA9555 is a 24-pin CMOS device that provides 16 bits of General Purpose parallelInput/Output (GPIO) expansion for I2C-bus/SMBus applications and was developed toenhance the NXP Semiconductors family of I2C-bus I/O expanders. The improvementsinclude higher drive capability, 5 V I/O tolerance, lower supply current, individual I/Oconfiguration, and smaller packaging. I/O expanders provide a simple solution whenadditional I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.The PCA9555 consists of two 8-bit Configuration (Input or Output selection); Input, Outputand Polarity Inversion (active HIGH or active LOW operation) registers. The systemmaster can enable the I/Os as either inputs or outputs by writing to the I/O configurationbits. The data for each Input or Output is kept in the corresponding Input or Outputregister. The polarity of the read register can be inverted with the Polarity Inversionregister. All registers can be read by the system master. Although pin-to-pin and I2C-busaddress compatible with the PCF8575, software changes are required due to theenhancements, and are discussed in Application Note AN469.
上传时间： 2013-11-13
上传用户：fredguo
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
The TJA1042 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing the differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1042 TJA
上传时间： 2014-12-28
上传用户：气温达上千万的
The TJA1051 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1051 TJA
上传时间： 2013-10-17
上传用户：jisujeke
The P82B96 offers many different ways in which it can be used as abus interface. In its simplest application it can be used as aninterface between bus systems operating from different supplyvoltages. Opto isolation between two bus systems is possible, andalso the availability of the Tx and Rx signals permits interfacing ofthe P82B96 with other bus systems which separate the forwardoutput path, from the backward input signal path.
上传时间： 2013-10-11
上传用户：洛木卓
8051单片机系统扩展与接口技术:第一节 8051 单片机系统扩展概述第二节 单片机外部存储器扩展第三节 单片机输入输出（I/O）口扩展及应用第四节 LED显示器接口电路及显示程序第五节 单片机键盘接口技术第六节 单片机与数模（D／A）及模数（A／D）转换1、地址总线（Address Bus，简写为AB）地址总线可传送单片机送出的地址信号，用于访问外部存储器单元或I/O端口。A 地址总线是单向的，地址信号只是由单片机向外发出。B 地址总线的数目决定了可直接访问的存储器单元的数目。例如N位地址，可以产生2N个连续地址编码，因此可访问2N个存储单元，即通常所说的寻址范围为 2N个地址单元。MCS—51单片机有十六位地址线，因此存储器展范围可达216 = 64KB地址单元。C 挂在总线上的器件，只有地址被选中的单元才能与CPU交换数据，其余的都暂时不能操作，否则会引起数据冲突。2、数据总线（Data Bus，简写为DB）数据总线用于在单片机与存储器之间或单片机与I/O端口之间传送数据。A 单片机系统数据总线的位数与单片机处理数据的字长一致。例如MCS—51单片机是8位字长，所以数据总线的位数也是8位。B 数据总线是双向的，即可以进行两个方向的数据传送。3、控制总线（Control Bus，简写为CB）控制总线实际上就是一组控制信号线，包括单片机发出的，以及从其它部件送给单片机的各种控制或联络信号。对于一条控制信号线来说，其传送方向是单向的，但是由不同方向的控制信号线组合的控制总线则表示为双向的。总线结构形式大大减少了单片机系统中连接线的数目，提高了系统的可靠性，增加了系统的灵活性。此外，总线结构也使扩展易于实现，各功能部件只要符合总线规范，就可以很方便地接入系统，实现单片机扩展。
上传时间： 2013-10-18
上传用户：assef
